IEI Technology AFL-08AH-N270-CR User Manual Download Page 84

Page: 84 / 115

AFL-08AH-N270-CR Panel PC

Page 70

USB Functions [Enabled]

Use the

USB Function

option to enable or disable the USB controllers.

Disabled

USB controllers are enabled

Enabled D

EFAULT

USB controllers are disabled

USB 2.0 Controller [Enabled]

The

USB 2.0 Controller

BIOS option enables or disables the USB 2.0 controller

Enabled D

EFAULT

USB function enabled

Disabled

USB function disabled

Legacy USB Support [Enabled]

Use the

Legacy USB Support

BIOS option to enable USB mouse and USB keyboard

support.

Normally if this option is not enabled, any attached USB mouse or USB keyboard does not

become available until a USB compatible operating system is fully booted with all USB

drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard

can control the system even when there is no USB driver loaded onto the system.

Disabled

Legacy USB support disabled

Enabled D

EFAULT

Legacy USB support enabled

Auto

Legacy USB support disabled if no USB devices are

connected

USB2.0 Controller Mode [HiSpeed]

The

USB2.0 Controller Mode

BIOS option sets the speed of the USB2.0 controller.

FullSpeed

The controller is capable of operating at full speed

12 Mb/s

Summary of Contents for AFL-08AH-N270-CR




















































































































Search results

Summary of Contents for AFL-08AH-N270-CR

Reviews:

Related manuals for AFL-08AH-N270-CR

Brands by name

Popular brands

IEI Technology AFL-08AH-N270-CR, User Manual

Search results

Summary of Contents for AFL-08AH-N270-CR

Reviews:

Related manuals for AFL-08AH-N270-CR

Brands by name

Popular brands