IDTECH ValueScan II User Manual Download Page 72

Page: 72 / 98

Code 11

Read:

Format

Data Digits

(Variable)

Checksum1

(Optional)

Checksum2

(Optional)

Checksum Verification:

The checksum is presented as the

sum module 11 of all data digits.

Checksum Transmission:

By setting Enable, checksum1

and checksum2 will be transmitted upon your selected

checksum verification method.

Max./Min. code length:

Refer to Max./Min. code length of

Code 39.

Truncate leading/ending:

Refer to Truncate leading/ending

of UPC-A.

Code ID setting:

Refer to Code ID setting of UPC-A.

Insertion group selection:

Refer to

Insertion group

selection of UPC-A.

Option Bar Code

Option

Alphanumeric

Entry

Read

Disable

Enable

＊

Checksum

Verification

Disable

One digit

Two digits

＊

Checksum

Transmission

Disable

Enable

＊

Program

Summary of Contents for ValueScan II



































































































Search results

Summary of Contents for ValueScan II

Reviews:

Related manuals for ValueScan II

Brands by name

Popular brands

IDTECH ValueScan II, User Manual

Search results

Summary of Contents for ValueScan II

Reviews:

Related manuals for ValueScan II

Brands by name

Popular brands