IDTECH ValueScan II User Manual Download Page 22

Page: 22 / 98

Indication

Power on alert:

After power-on the scanner will generate an

alert signal to indicate a successful self-test.

LED indication:

After each successful reading, the LED

above the scanner will light up to indicate a good barcode

read.

Beeper indication:

After each successful read, the scanner

will beep to indicate a good barcode read, and its Beep

loudness, Beep tone freq. and Beep tone duration are

adjustable.

Beep loudness/Beep tone freq./Beep tone duration:

You

can adjust Beep Loudness, Beep tone and Beep duration for

a good read to your personal preference.

<note >

In Beep tone frequency setting, 00~10 are used to

set to Melody 0~10 and not for tone frequency 0~1000 Hz.
The other values from 11~99 are defined as the beep tone
frequency.

Summary of Contents for ValueScan II



































































































Search results

Summary of Contents for ValueScan II

Reviews:

Related manuals for ValueScan II

Brands by name

Popular brands

IDTECH ValueScan II, User Manual

Search results

Summary of Contents for ValueScan II

Reviews:

Related manuals for ValueScan II

Brands by name

Popular brands