background image

 

 

 

FCC Regulatory Compliance 

Notices Class B Equipment 

This equipment has been tested and found to comply with the limits for a Class B digital device 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses, and can 
radiate radio frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications. However, there is no guarantee that 
interference will not occur in a particular installation. This device complies with part 15 of the FCC 
rules. Operation is subject to two conditions: (1) This device may not cause harmful interference, 
and (2) this device must accept any interference received, including interference that may cause 
undesired operation.

 

If this equipment does cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try and correct the 
interference by one or more of the following measures:

 

  Reorient or relocate the receiving antenna.  

  Increase the separation between the equipment and the receiver. 

  Connect the equipment into an outlet on a circuit different from that to which the receiver is 

connected.  

  Consult the dealer or an experienced radio/TV technician for help.  

Changes or modifications to the ViVOpay Kiosk III not expressly approved by ViVOtech could 
void the user's authority to operate the ViVOpay Kiosk III. 

IC Compliance Warning 

Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) 
this device must accept any interference received, including interference that may cause 
undesired operation.

 

Cautions and Warnings 

 

Caution: 

The ViVOpay Kiosk III should be mounted 1-2 feet away from other 

ViVOpay Kiosk IIIs. Can be adjusted based on lane setup.

 

 

Caution: 

Danger of Explosion if battery is incorrectly replaced. Replace only with 

same or equivalent type recommended by the manufacturer. Discard used batteries 
according to the manufacturer’s instructions.

 

 

Warning: 

Avoid close proximity to radio transmitters which may reduce the ability of 

the reader.

 

 

IC Compliance 

This device complies with Industry Canada license

exempt RSS standard(s). Operation is subject t

o the following two conditions: (1) this device may not cause interference, and (2) this device must a
ccept any interference, including interference that may cause undesired operation of the device.  
Le present appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exem
pts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) l’appareil ne doit pas pr
oduire de brouillage,et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, 
même si le brouillage est susceptible d’en compromettre le fonctionnement.

  

 

 

Summary of Contents for Kiosk III



















Reviews: