background image

 

ViVOpayKiosk III UserManual 

 

 

 

Page14 of 18

 

2.6

 

Using

 

the

 

ViVOpay

 

Kiosk

 

III

 

to

 

Make

 

a

 

Purchase

 

2.6.1

 

Presenting

 

Cards,

 

Fobs,

 

or

 

NFC

 

Phones

 

 

Your new ViVOpayKiosk III allows for credit/debit card purchases using the new contactless 
technology. 

Present the card/fob/phone in close proximity to the front portion of the antenna module. Present 
the card/fob/phone so that maximum surface area is parallel to the antenna module as shown 
below. The antenna should beep and all four green LEDs should illuminate briefly to indicate a 
successful test. 

 

This tests the antenna's ability to read the RFID test card. If unsuccessful, there will be no reaction 
from the reader. If you use a test card and the ViVOpay reader is attached to theViVOpay Kiosk III 
Controller, a dummy transaction can be tested. The transaction will not be authorized and will 
come back with a response, but will at least test for end-to-end connectivity.  

2.6.2

 

Making

 

a

 

Purchase

 

1.  After the transaction has been entered on the kiosk control panel, the customer should 

present their card/fob/phone in close proximity so that maximum surface area is parallel to 
the antenna.  

•   A single beep and all four LEDs briefly flashing indicates the card/fob/phone has been read 

correctly. 

3 Installation 

Points 

 

  The ViVOpay Kiosk III is designed to be mounted on a metal surface and in close proximity to 

any internal motors and electrical devices that may be operating inside the kiosk.However, the 
ViVOpayKiosk III is susceptible to RF and electromagnetic interference. It is important that the 
unit not be mountednear (within 3 or 4 feet) large electric motors, computer UPS systems, 
microwave transmitters, anti-theft devices, radio transmitters, communications equipment and 
so on. 

  Close proximity of metal to the RF-emitting end of the antenna can greatly reduce the range of 

the antenna. See the precautions described in 

Flush Mounting the Kiosk III Antenna

  Tie all cables neatly with nylon cable-ties and route them so that they are inaccessible and 

invisible to customers. Label the cable ends, host, ViVOpay and power, to simplify connection 
testing or component replacement. 

Summary of Contents for Kiosk III



















Reviews: