IDT 89HPEB383 User Manual Download | Manualshive

Page: 94 / 264

background image

9. Error Handling > Other Errors

80

PEB383 User Manual

July 25, 2011

Integrated Device Technology, Inc.

Confidential - NDA Required

9.4.1

PCIe Completion Timeout Errors

The PCIe Completion Timeout function allows requestors to abort a non-posted request if the
completion does not arrive within a reasonable period of time. When bridges act as initiators on PCIe
on behalf of internally generated requests, and requests forwarded from a secondary interface in PCI
mode, they act as endpoints for requests that they take ownership. When the PEB383 detects a
completion timeout it responds as if a completion with Unsupported Request status has been received
and follows the rules for handling Unsupported Request Completions as described in

Request Completion Status”

. In addition, the bridge takes the following actions:

1.

CTO bit is set in

“PCIe Uncorrectable Error Status Register”

2.

Error Fatal or Non-Fatal message is generated on PCIe as per the severity level of the CTO bit in

“PCIe Uncorrectable Error Severity Register”

if CTO Mask bit is clear in

“PCIe Correctable Error

Mask Register”

and either SERR_EN bit is set in

“PCI Control and Status Register”

or

FTL_ERR_EN/NFTL_ERR_EN bit is set in

“PCIe Device Control and Status Register”

3.

S_SERR bit is set in

“PCI Control and Status Register”

if an error message (Fatal/Non-Fatal) is

generated and the SERR_EN bit is set in

“PCI Control and Status Register”

9.4.2

PCI Delayed Transaction Timeout Errors

If a delayed transaction timeout is detected the PEB383 does the following:

1.

Error Fatal or Non-Fatal message is generated on PCIe as per the severity level of DTDTE bit in

“PCIe Secondary Uncorrectable Error Severity Register”

, if DTDTE Mask bit is clear in

Secondary Uncorrectable Error Mask Register”

or DISCARD_SERR bit is set

Control and Interrupt Register”

and either SERR_EN bit is set in

“PCI Control and Status

or FTL_ERR_EN/NFTL_ERR_EN bit is set in

“PCIe Device Control and Status

2.

No Header is logged

3.

S_SERR bit is set in

“PCI Control and Status Register”

if an error message (Fatal/Non-Fatal) is

generated and SERR_EN bit is set in

“PCI Control and Status Register”

9.5

Other Errors

PCI devices can assert SERR# when detecting errors that compromise system integrity. When the
PEB383 detects SERR# on the secondary interface, it does the following:

1.

S_SERR bit is set in

“PCI Secondary Status and I/O Limit and Base Register”

2.

Error Fatal or Non-Fatal message is generated on PCIe as per the severity level of SERR_AD bit in

“PCIe Secondary Uncorrectable Error Severity Register”

if SERR_AD Mask bit is clear in

Secondary Uncorrectable Error Mask Register”

or SERR_EN bit is set in

“PCI Bridge Control and

Interrupt Register”

and either SERR_EN bit is set in

“PCI Control and Status Register”

FTL_ERR_EN/NFTL_ERR_EN bit is set in

“PCIe Device Control and Status Register”

3.

SERR_AD bit is set in

“PCIe Secondary Uncorrectable Error Status Register”

4.

SUFEP field is updated in

“PCIe Secondary Error Capabilities and Control Register”

5.

No Header is Logged for SERR# assertion

«
...
92
93
94
95
96
...
»

Summary of Contents for 89HPEB383









































































































































































































































































Reviews:

No comments

Related manuals for 89HPEB383

Brand: DAQ system Pages: 33

Brand: Barco Pages: 2

Brand: FastVDO Pages: 16

Brand: Racelogic Pages: 2

RADEON 8500 MAC EDITION

Brand: ATI Technologies Pages: 45

Brand: SIB Pages: 4

Brand: StarTech.com Pages: 11

Brand: MSI Pages: 2

Brand: NEC Pages: 8

Brand: NEC Pages: 22

Brand: NEC Pages: 34

Brand: NEC Pages: 72

Brand: NEC Pages: 90

Brand: NEC Pages: 99

Brand: NEC Pages: 97

Brand: NEC Pages: 343

Brand: Lava Pages: 1

Brand: Contec Pages: 69

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands