background image

Ezi4 Alarm Panel  700-497-02A  Issued April 2012   

 

 

 

 

 

91 Escom Road  •  New Germany • 3610 • South Africa • P O Box 738 • New Germany • 3620 • South Africa 

Tel: +27 (0)31 705 1373  

 Fax: +27 (0)31 705 4445 

 e-mail: [email protected] 

  www.inhep.com 

 

INHEP ELECTRONICS HOLDINGS (Pty) Ltd 

Reg. No. 2007/002578/07

 

 

 PGM Outputs 1  

PGM  1  is  primarily  designed  to  be  connected  to  a  LED  (no  resistor  required).  It 
displays the Arm Status. If the output is “ON” the Panel is in the armed state. If the 
output is “OFF” the panel is in the disarmed state. 

PGM Outputs 2 

When  a  new  Alarm  condition  is  generated,  PGM  2  will  turn  on  momentarily  for  1 
second.  This  output  is  designed  to  link  the  Ezi4  Alarm  Panel  to  either  a 
communicator input or to link the Ezi4 Alarm Panel to another panel.   

Display 

Five  Light  emitting  diodes  (LEDs)  are  mounted  on  the  lid  of  the  alarm  panel  as 
shown in figure 4 below. The four red LEDs display the status of the Alarm Zones. 
The fifth green LED indicates that the panel is “running” and shows the status of the 
tamper input. 

  

 

 

 

 

 

 

Figure 4: Front Cover Labelling 

Zone 4

Zone 3

Zone 2

Zone 1

Power

Ezi4

Alarm Panel

Zone 4

Zone 3

Zone 2

Zone 1

Power

Ezi4

Alarm Panel

Zone 4

Zone 3

Zone 2

Zone 1

Power

Ezi4

Alarm Panel

Summary of Contents for Ezi4









Reviews: