background image

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Warranty 

  

Inhep  Electronics  Holdings  (Pty)  Ltd  guarantees  all  IDS  Control 
Panels  against  defective  parts  and  workmanship  for  24  months 
from  date  of  purchase.    Inhep  Electronics  Holdings  shall,  at  it’s 
option, repair or replace the defective equipment upon the return 

of  such  equipment  to  any  Inhep  Electronics  Holdings  branch.  
This  warranty  applies  ONLY  to  defects  in  components  and     
workmanship  and  NOT  to  damage  due  to  causes  beyond  the 
control of Inhep Electronics Holdings, such as incorrect voltage, 
lightning damage, mechanical shock, water damage, fire damage 
or damage arising out of abuse and improper application of the 
equipment. 

  
  

NOTE: Wherever possible, return only the PCB to                     

Inhep Electronics Holdings service centres. 

DO NOT return the enclosure. 

  

The IDS Ezi4 Alarm Panel is a product of                                               

IDS (Inhep Digital Security) and is manufactured by                                                  

Inhep Electronics Holdings (Pty) Ltd 

  

  

WARNING 

For safety reasons, only connect equipment with a         

telecommunications compliance label.  This includes     

customer equipment previously labeled permitted             

or certified. 

91 Escom Road  •  New Germany • 3610 • South Africa • P O Box 738 • New Germany • 3620 • South Africa 

Tel: +27 (0)31 705 1373  

 Fax: +27 (0)31 705 4445 

 e-mail: [email protected] 

  www.inhep.com 

 

INHEP ELECTRONICS HOLDINGS (Pty) Ltd 

Reg. No. 2007/002578/07

 

 

Summary of Contents for Ezi4









Reviews: