IDS 816, User Manual

Page: 18 / 28

IDS816 User Manual 700-283-01H Issued January 2009
18
Table 2 User Code Properties
Zone
Zone Zone
Zone LED
LED LED
LED Property
Property Property
Property
2 Duress code
3 Arm to disarm code [Maid’s code]
4 Global arm/disarm code
13.5.1 13.5.1 13.5.1 13.5.1 Explanation of Explanation of Explanation of Explanation of U U U User Code ser Code ser Code ser Code Properties Properties Properties Properties
13.5.1.1
13.5.1.1 13.5.1.1
13.5.1.1 Duress Code
Duress Code Duress Code
Duress Code
This is a special 4 (default) or 6 digit user code (check the code length with your installer) which
should only be used in the unique situation where an intruder forces one to disarm the system
“under duress”.
When the DURESS CODE is entered, the control panel disarms normally - however, a DURESS
REPORTING CODE is transmitted to the monitoring company to inform them that you have been
forced to disarm the control panel by an intruder.
It is advisable to choose a code that can be easily remembered by all family (or staff) members.
13.5.1.2
13.5.1.2 13.5.1.2
13.5.1.2 Maid’s Code
Maid’s Code Maid’s Code
Maid’s Code
This code may be used to limit access to the premises. The MAID’S CODE will only disarm the system if
the same code was used for arming. If armed with a code other than this code, the system will view an
attempt to disarm using the MAID’S CODE as an invalid entry. Any valid user code will disarm the system
if it has been armed with the MAID’S CODE.
13.5.1.3
13.5.1.3 13.5.1.3
13.5.1.3 G
G G
Global
lobal lobal
lobal A
A A
Arm
rm rm
rm/D
/D /D
/Disarm
isarm isarm
isarm C
C C
Code
ode ode
ode
This code, when entered, will either arm or disarm the partitions assigned to that user depending on their
status. If both partitions are disarmed, entering a global code will arm both partitions. If both partitions are
armed, entering a global code will disarm them. In the case where one partition is armed and the other
disarmed, entering a global code at the keypad of the armed partition will disarm that partition and
entering a global code at the keypad of the disarmed partition will arm that partition.
13.6
13.6 13.6
13.6 Assign
Assign Assign
Assign a
a a
a U
U U
User
ser ser
ser C
C C
Code
ode ode
ode to Partitions
to Partitions to Partitions
to Partitions –
––
– Option 5
Option 5 Option 5
Option 5
Hold down the [*] key until the beep,
then enter [MASTER CODE] [*] [5] [*] [USER CODE] [*] [ZONE LED No] [*] [#]
1.
Enter the User Program Mode as per steps 1 to 4 on page 14.
2. Press the [5] key followed by the [*] key to select programmable option 5. The READY and
ARMED LED’s will flash simultaneously.
3. Enter the [USER CODE] followed by the [*] key.
4. The READY indicator will flash and the AWAY indicator will be on.
5. The partitions to which the user code is assigned are displayed by the by the zone LED’s. If zone
LED 1 is on, the user code can arm or disarm partition 1. If zone LED 2 is on, the user code can
arm or disarm partition 2. It is possible to program codes to arm/disarm both partitions.
6. To select which partitions the user code may arm or disarm, toggle zone LED’s by entering the
[ZONE LED NUMBER] followed by the [*] key.