background image

 English 

 

 

4.

 

SAFETY RULES 

 

KEEP THIS INSTRUCTION MANUAL 

Before starting any operation with ASTRA STEAMER HYBRID read the following instructions 

carefully. Store the manual for later use or for subsequent owners. 

 

The manufacturer is not responsible for any damage caused by improper use of the machine or noncompliance 
with the instructions. 

Do not make substitutions or modifications to any of the parts of the machine 

The voltage indicated on the type plate must correspond to the voltage of the electrical source. 

The electrical grid to which the machine is connected must be made according to current National Safety 
Directives. 

Before unplugging the machine make sure that you have turned it off by the main switch 1 (fig.01)  

Do not pull the power cord to disconnect the machine. To avoid damaging the cord, unplug directly at the wall 
outlet.  

Make sure that the power cord or extension cables are not damaged by running over, pinching, dragging or 
similar. Protect the cable from heat, oil, and sharp edges.

Do not use the Steamer if the power cord has been damaged.  

Do not use extension cords that are not approved / recommended by the manufacturer as they can increase 
fire hazard. 

Do not repair a damaged cable.  

If the cable needs to be substituted please contact Assistance.  

Never touch the electric outlet with wet hands.  

Do not use the machine while barefoot.  

Do not use the machine in proximity of full sinks, tubs, or basins.  

Do not submerge the machine or any of its components in water or any other liquid.  

It is strictly forbidden to operate the machine in areas with a potential explosion hazard.  

Do not use the machine in proximity of hazardous/toxic substances.  

Do not leave the machine on heat-sensitive surfaces while still hot.  

Do not leave the machine exposed to weather and environmental hazards. 

Do not place the machine close to ovens, stoves or any other heat source.  

Do not expose the machine to extreme temperatures.  

Summary of Contents for Astra Steamer Hybrid

































Reviews: