FDX-16 User
’s Guide
70
Item
Description
Optical output slot board (*6)
Output
4 outputs
Video
Digital optical
signals for
extension
TMDS clock: 25 MHz to 165 MHz
HDMI (*7) / DVI 1.0, HDCP 1.4 supported
Format
VGA / SVGA / XGA / WXGA (1280x768) / WXGA (1280x800) / Quad-VGA / SXGA /
WXGA (1360x768) / WXGA (1366x768) / SXGA+ / WXGA+ / WXGA++ / UXGA / WSXGA+ / WUXGA
WUXGA: only Reduced Blanking is supported.
480i / 480p / 576i / 576p / 720p / 1080i / 1080p
Audio
Digital optical
signals for
extension
Multi channel linear PCM: up to 8 channels
Sampling frequency: 32 kHz to 192 kHz, quantization bit rate: 16 bit to 24 bit
Cable
Duplex fiver cable, SFP module (2 LC connectors) (*8)
Recommended polishing
method (*9)
SFP module for multimode: PC polishing (recommended)
SFP module for singlemode: UPC polishing (recommended), SPC polishing (APC polishing is not supported)
Max. extension distance (*10)
Multimode fiber (OM3): 985 ft. / 300 m
Multimode fiber (OM4): 0.62 miles / 1 km
Singlemode fiber (OS1): 2.9 miles / 4.7 km
Digital output slot board
Output
4 outputs
Video
HDMI/DVI
TMDS single link, TMDS clock: 25 MHz to 225 MHz
HDMI Deep Color supported (*1) / DVI 1.0, HDCP 1.4 supported, built-in cable equalizer
Format
VGA to QWXGA (dot clock: 25 MHz to 165 MHz)
WUXGA / QWXGA: only Reduced Blanking is supported.
480i / 480p / 576i / 576p / 720p / 1080i / 1080p
Audio
Digital audio
Multi channel linear PCM: up to 8 channels
Sampling frequency: 32 kHz to 192 kHz, quantization bit rate: 16 bit to 24 bit
Connector
DVI-I (29 pin), female (Analog signals cannot be used.)
Max. extension distance
33 ft. to 131 ft. / 10 m to 40 m (*11)
Function
Video and audio are switched separately (when audio unit MAU-1616 (optional) is connected);
I/O slot board and CPU slot board can be replaced without removing from the rack;
startup memory; preset memory (32 memories
＋
startup memory); last memory; key lock; anti-snow (*13);
connection reset (*14); the number of inputs and outputs can be customized by 4 inputs or 4 outputs
Alarm output
1output terminal block (2 pin), power monitor, fan monitor
External
control
RS-232C
1 port D-sub9 pin connector, male
LAN
1port RJ-45 connector 10Base-T / 100Base-TX (Auto Negotiation), Auto MDI / MDI-X
Optional (MAU-1616)
1port D-sub25 pin connector, female
General
Power supply voltage
AC
～
100 V - 240 V
±
10%, 50 Hz / 60 Hz
±
3 Hz
Power consumption
(*15)
At maximum HDBaseT extension input / output
configuration
: about 212 W
At maximum optical input / output slot board
Multimode fiber
: about 244 W
Singlemode fiber
: about 255 W
At maximum digital input / output slot board
configuration
: about 123 W
Dimensions
About 16.93 (W) x 5.2
(H) x 13.88 (D)” / 430 (W) x 132 (H) x 350 (D) mm (EIA rack 3U, not including projections)
Weight (*15)
At maximum HDBaseT extension input / output
configuration
: 23.8 lbs. / 10.8 kg
At maximum optical input / output slot board
Multimode fiber
: 27.34 lbs. / 12.4 kg
Singlemode fiber
: 27.34 lbs. / 12.4 kg
At maximum digital input / output slot board
configuration
: 21.6 lbs. / 9.8 kg
Temperature
Operating temperature: 32 °F to 104 °F / 0 °C to +40 °C
Storage temperature: -4 °F to +176 °F / -20 °C to +80 °C
Humidity
Operating/ Storage humidity: 20 % to 90 % (Non Condensing)
Included items
RS-232C cable (5.9 ft./1.8 m). power supply cable (5.9 ft./1.8 m), rack mounting brackets, terminal block (2 pin)
*1
36 bit / pixel (12 bit / component) Deep Color is supported. xvYCC, Lip Sync, 3D, ARC, HEC and CEC are not supported.
*2
DVI signals protected by HDCP are not supported. For those signals, use HDC-TD100 as the transmitter.
*3
RJ-45 (HDBaseT connector) is the special connector to extent video and audio signals using a Cat5e / Cat6 twisted pair cable. Use this connector
only for IDK
’s twisted pair cable transmitter and receiver; do not use it for LAN devices.
*4
T568A or T568B straight. For longer than 164.04 ft. / 50 m, Cat6 is recommended.
*5
If the FDX is connected to a device which is in significantly bad condition, video may be interrupted. Since some LC monitors operates unsteadily,
check the operation beforehand or contact us.
*6
Use OPF-H1000-A as the extender connected to an optical I/O slot board.
*7
Deep Color, xvYCC, Lip Sync, 3D, ARC, HEC and CEC are not supported.
*8
The standard SFP specification is as follows.
*9
Polishing methods other than the recommended method can be used, but the extension distance will change due to an increase in return loss.
*10
The mentioned maximum extension distance is acquired when the recommended polishing method fiber is used, there is no connection through the
path, and the allowable bending radius is not exceeded.
*11
The transmission distance depends on connected devices. The distance above is the maximum transmission distance when a cable made by IDK
(AWG24) is used and signals, 1080p 60 Hz 24 bit/pixel (8 bit/component), are input or output. If the connected device is not matched to the FDX or if
other makers' cables are used, video signals can be unstable or video signals cannot be output, even though the transmission distance is within the
information above.
*12
DVI signals protected by HDCP are not supported. For those signals, use HDC-RD100 as the receiver.
*13
Anti-snow feature fixes snowy noise automatically that is a specific symptom of the signal having HDCP. The problem occurs mainly during start-up.
This feature is invalid when snow noise has already occurred before start-up or when snow noise occurs due to a bad status of transmission line.
*14
This feature automatically resolves problems which can be resolved by unplugging and plugging in connectors. This feature works only for this
device’s outputs, and this may be disabled if another device is connected between this device output and display device.
*15
For power consumption and weight at each I/O slot board combination, please contact us.
