background image

Operator Manual        ilex

55

 

 

L280-0975 REV A 

 

www.imagediagnostics.com

                        Page 4 

4.

 

Safety Hazards 

 

 
 
 

 

  

 

 

 

 

WARNING!

 

Do not modify this equipment without authorization of the 

manufacturer. 

 

CAUTION!

 

Do NOT store liquids above any electrical devices. 

CAUTION!

 

Caution should be used when moving the system over 

uneven or sloped surfaces.

 

WARNING!

 

Do NOT jump any curbs or steps over 3/8” (10mm) in 

height with this equipment. Approach all obstacles slowly. 

Operator must use a ramp to allow the casters to roll up 

and over the vertical edge for over 3/8” (10mm).

 

WARNING!

 

It is the user’s responsibility to make sure the equipment is 

safe and operates properly prior to use.

 

WARNING!

 

Do NOT mount a display monitor weighing more than 96 

LB (44 kg).

 

WARNING!

 

Connecting any electrical equipment to the socket outlets 

of the ilex55 creates a new ME (Medical Electrical) 

Equipment unit possibly resulting in a reduced level of 

safety.  Once this is done, the responsible organization 

must refer and comply to the standard IEC 60601-1. 

Summary of Contents for Ilex 55





























Reviews: