background image

Page 8  

0901048 Rev. C 

 

Description of Screen 

Display 

16. 

To change the units of measure, use the SCROLL button to toggle between Fahrenheit/Gallons and Celsius/Liter. 

 

Press ENTER to advance to the next screen. 

 

17. 

To choose a low level setting, use the SCROLL button to toggle between N/C and N/O. 

 

Important: 

If you are using a flow meter or the time based feature, you have the choice between N/C (normally closed) and N/
O (normally open). The option you choose should match the low level alarm that you are using. 

 

Press ENTER to advance to the next screen. 

 

18. 

To set the alarm sound on or off, use the SCROLL button toggle to between on and off. 

 

Press ENTER to advance to the next screen. 

 

19. 

To set the dispensing volumes, use the SCROLL button to toggle between volume A and volume B. Use the UP and 
DOWN buttons to set the numerical value for the amount of detergent you wish to dispense for each volume. 

 

Press ENTER to advance to the next screen. 

 

20. 

To set your preferred method of dosing, use the SCROLL button to toggle between Time Based Dosing and Flow 
Metered Dosing. 

 

Press ENTER to advance to the next screen. 

 

21. 

If you selected Flow Metered Dosing for the previous step, you will see the auto prime screen. To set auto prime to 
on or off, use the SCROLL button to toggle between on and off. Note: This feature is only available with Flow 
Metered Dosing. 

 

Press ENTER to advance to the next screen. 

 

PRESS SCROLL TO 

SELECT WHICH UNITS 

TO USE  

PRESS SCROLL TO SELECT LOW 
LEVEL STATE 

 

PRESS SCROLL TO 
TURN ALARM SOUND 
ON OR OFF 

SCROLL TO ENTER 

VOLUME A  025 ml 

VOLUME B  050 ml 

PRESS SCROLL TO 

SELECT DOSE MODE 

 

PRESS SCROLL TO  

SELECT SCROLL MODE 

 

PRESS SCROLL TO 

SELECT WHICH UNITS 

TO USE  

PRESS SCROLL TO SELECT LOW 
LEVEL STATE 

 

PRESS SCROLL TO  TURN AUTO 
PRIME ON OR OFF 

 

Summary of Contents for Knight DoseTech DMS



























Reviews: