background image

 

i-B350L -CC 

– Hardware User Manual | 20. September 2019 

 

Copyright © 2019 IDENTEC SOLUTIONS. All rights reserved. 

5

 

Safety Instructions 

The system described in this manual is for exclusive operation of trained employees. Only qualified personnel that 
have knowledge of the potential dangers involved should perform the installation, settings, maintenance and repair 
of the units used. 

 

Operational Safety 

The correct and safe use of these systems assumes that operating and service personnel follow the safety 
measures described in the manual alongside the generally acceptable safety procedures. 

If there is a possibility that safe operations cannot be guaranteed, the system must be switched off, secured against 
accidental use and the service unit responsible immediately informed. 

 

Safety Documents 

The i-B350L CC was designed, tested and supplied in perfect condition according to document IEC/EN 60950-1 
Safety Requirements. 

 

Condensate / Change of Temperature 

To avoid condensation in the system, the unit must be allowed to slowly adjust itself to warmer temperatures after 
removal from cold and cool environments.  

 

Connections / Power Supply 

The supply circuits must comply with the conditions set out for the SELV circuits (see EN 60950-1). 

During maintenance damage could occur if printed circuit boards or cables are connected or disconnected whilst 
the power supply is still on. Therefore, only work on the connection and the components when they are not live. 

 

Battery Inside 
 

All system tags contain a battery; therefore, the following warning should be heeded:  
 

 
WARNING

 - Fire, explosion and burn hazard risk of explosion if battery is replaced by an 

incorrect type. Do not recharge, short circuit, crush, disassemble, heat above 100 °C (212 °F).  
Do not incinerate, or expose contents to water

 

 

 

Spare Parts 

We recommend that only personnel, original products, spare and replacement parts authorized by IDENTEC 
SOLUTIONS be used for installation, service and repair. IDENTEC SOLUTIONS does not accept any responsibility 
for materials used, work carried out or possible consequences from unauthorized third party vendors. 

 

Glossary 

 

SELV 

Safety Extra Low Voltage 

– Protective measure against dangerous body currents. Protective first voltage, circuit not floating. 

 

 

 

Summary of Contents for i-B350L-CC

















Reviews: