background image

36

 

sERVICINg

Indep Combi - 

Installation and Servicing

3

38  CLEaNINg ThE hEa T ExChaNgER

note: Ensure the condensate trap/siphon 
is fully drained before cleaning. 
Refer to 
Frame 50.

1.

  Remove ignition and flame detection 

electrodes. Refer to Frames 45 & 46.

2.  It is advisable to replace the sump cover 

prior to the water flush process.

3. 

Thoroughly flush the heat exchanger 

by pouring water into the top of the 
combustion chamber ensuring the full top 
area is covered. 

4.  Remove the sump cover and clean loose 

deposits from the sump.

5.  Inspect the ignition and detection 

electrodes. Ensure that they are clean 
and in good condition - replace if 
necessary.

6. 

Re-fit the ignition and flame detection 

electrodes, ensuring that both earth tabs 

are fitted to ignition electrode.

7.  Check that the ignition and detection gaps 

are correct. Refer to Frames 45 & 46.

1

Ignition Electrode

Flame Detection

Reassemble the boiler in the following order:

1.  Ensure that the condensate trap/siphon is full of water.

2.

  Refit the burner ensuring the sealing gasket is correctly 

positioned and free from damage (tighten the 4 fixing screws 

in the sequence shown below).

3. 

Refit the fan / venturi assembly ensuring the retaining tabs 

are correctly positioned and the sealing gasket is correctly 
positioned and free from damage.

4.  Reconnect the fan electrical leads.

5.

  Remove the sump cover and refit the lower flue manifold as 

shown.

39  REassEMBL y

5

1

6. 

Refit the sump cover.

7.

  Refit the boiler front panel.  

IMpORTaNT.   Ensure that the boiler front panel is 

correctly fitted and that a good seal is made.

8.  Swing the control box back into its working position and 

secure.

9.  Turn on the gas supply at the gas service cock.

10. Reconnect the electrical supply.

3

2

4

sER

VICIN

g

Summary of Contents for INDEPENDENT C35









































































Reviews: