background image

Ideal Boilers

, P.O. Box 103, National Ave, Kingston Upon Hull, HU5 4JN. Tel.

01482 492251 Fax. 01482 448858. Registration No. London 322 137.

Ideal Stelrad Group 

pursues a policy of continuing improvement in the design and performance

of its products.  The right is therefore reserved to vary specification without notice.

Ideal Consumer Helpline

Tel: 01482 498660

www.idealheating.com

8

CLEARING THE PRESET TIMES

The programmer comes with preset time periods for Central
Heating and Hot Water.  These can be individually cleared prior
to user programming using the following sequence.

DISPLAY SHOWS time / day

and backlight is OFF

DISPLAY SHOWS time / day

and backlight is ON

The left hand “Timed” is flashing, together

with the Radiator symbol and the word

“PROG” is showing

The left hand “Timed” is flashing, together
with the Tap symbol and the word “PROG”

is showing

Radiator (or Tap) symbol is steady.

The seven days of the week are flashing

“1” flashes, indicating that you have

selected period 1 on the days shown

“ON” flashes, and a time is showing

Use Up and Down Buttons to set

chosen day. Select MON-SUN

S

S

P

P

Select period 2 or 3 as required.

Select DEL. This will exclude this time

period altogether

Press ‘PROG’ button 

briefly

Press ‘PROG’ button 

briefly

For Hot Water

For Heating

Press up arrow twice or down
arrow three times until . .

is the PROG button

is the SELECT button

are the UP and DOWN buttons

P

S

S

206104-1.pmd

26/05/2010, 16:01

12

Summary of Contents for ESPRIT 2 24














Reviews: