IDEAL British Gas 100 RD2 Installation And Servicing Manual Download

Page: 12 / 44

British Gas 100 & 125 RD2 -

Installation & Servicing

INSTALLATION

7 BOILER ASSEMBLY - Exploded View

100 shown with casing removed .

Fan sensor

Tie rod

Mex 1852

Data badge

Return sensor

Overheat sensor

Flow

sensor

16.

Front plate assy.

18.

Burner manifold.

28.

Gas cock.

38.

Pressure switch.

41.

Air inlet duct.

42.

Turret access cover assy.

46.

Boiler base plate.

47.

Baseplate heat shield.

49.

Flue baffle.

65.

Control box.

92.

Thermostat bush.

LEGEND

Heat exchanger assembly.

Front section.

Centre section.

Section alignment rings and 'O' rings.

Back section.

Flow thermistor sensor pocket.

6A.

Return thermistor sensor pocket.

6B.

O/heat thermostat sensor pocket.

Distributor tube.

Combustion chamber.

12.

Collector hood.

14.

Fan assembly.

INST

ALLA

TION

Summary of Contents for British Gas 100 RD2













































Search results

Summary of Contents for British Gas 100 RD2

Reviews:

Related manuals for British Gas 100 RD2

Brands by name

Popular brands

IDEAL British Gas 100 RD2, Installation And Servicing Manual

Search results

Summary of Contents for British Gas 100 RD2

Reviews:

Related manuals for British Gas 100 RD2

Brands by name

Popular brands