IDEAL 222140 Installation Manual Download | Manualshive

Page: 16 / 16

background image

www.idealboilers.com |

welcome to our ideology

Hereby, Ideal Boilers Ltd declares that this device (model 222140) is in

compliance with: Directive

2014/53/EU.

The full text of the EU declaration of conformity is available at the

following internet address

www.idealboilers.com

UIN: 223827 A02

Ideal Boilers Ltd

National Avenue

Hull, HU5 4JN
T: 01482 498660

E: [email protected]

RF frequency: 2405 –2480MHz

Max. RF output power: 10dBm

«
...
14
15
16

Summary of Contents for 222140

















Reviews:

No comments

Related manuals for 222140

IntelliZone2 ZoneStat

Brand: WaterFurnace Pages: 2

Brand: Omega Engineering Pages: 2

THERMO-FIXX 0123 Series

Brand: KWB Pages: 24

Brand: ThermoPro Pages: 36

Brand: Aircalo Pages: 4

Brand: LEGRAND Pages: 68

Brand: Xavax Pages: 39

Brand: Hanna Instruments Pages: 15

Brand: Termoventiler AB Pages: 4

ACONT800 Series

Brand: American Standard Pages: 52

T19XWHB-7-RF-APP(SL)

Brand: Saswell Pages: 70

Checktemp HI 98501

Brand: Hanna Instruments Pages: 2

Grow With Me 03110

Brand: Summer Pages: 7

Brand: RNIB Pages: 12

Brand: Warmup Pages: 4

Brand: Warmup Pages: 24

Brand: Vimar Pages: 40

Brand: TMS Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands