![background image](http://html1.mh-extra.com/html/idatalink/ads-tbsl-c1/ads-tbsl-c1_install-manual_3587401004.webp)
install guide
Version française disponible en ligne au www.idatalink.com
transponder Bypass
chrysler / dodge / Jeep
Page 4 of 5
ADS-TBSL-C1
20071224
www.idatalink.com
For technical assistance, contact your distributor or visit www.idatalink.com/support
© 2007 ADS Inc.
NOTICE:
the manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself
or to the installed device. this device must be installed by a certified technician. this guide has been written for properly trained technicians; a certain level of skill &
knowledge is therefore assumed. please review the installation guide carefully before beginning any work.
www.idatalink.com
For technical assistance, contact your distributor or visit www.idatalink.com/support
© 2007 ADS Inc.
PROGRAMMING PROCEDURE
1
2
Insert the vehicle key into the ignition.
Turn the ignition to the “ON” position.
Wait for the LED to illuminate green
for
2 SECONDS
.
Programming is complete.
VEHICLE PROGRAMMING
ON
LED “ON” 2 SEC
1
2
NOTE
MODE SELECTION
1X
2X
PRESS
TO TOGGLE
BETWEEN MODES
PRESS + HOLD
Should you wish to change the installation mode,
follow the “Factory Reset” instructions as detailed below.
Press and release the programming button to select installation mode.
To register selection,
Hold the programming button down
until the LED displays a solid green light
.
OR
IDATALINK MODE
STANDARD MODE
LED flashes once
LED flashes twice
REMOTE STARTER
with Data Port
REMOTE STARTER
without Data Port
2
4
Wait approximately 15 seconds
for security light to flash, indicating
you have accessed “Learning mode”.
A warning chime will also be heard.
Turn the ignition to the “OFF” position
and remove key from ignition.
Hold the module to the ignition cylinder.
And power the main ignition
using a 10 Amp fused test lead.
(Note: If you encounter power loss
during this step, you will need to exit
learning mode and restart transponder
programming from step 1.
The security light will start flashing,
indicating you are now in programming
mode.
DO NOT INTERRUPT IGNITION until the
security light stops flashing.
Insert the first vehicle key into the ignition.
Turn the ignition to the “ON” position.
Security light on cluster will illuminate.
Once, the security light turns off,
turn the ignition to the “OFF” position
and remove key from ignition cylinder.
TRANSPONDER PROGRAMMING
ON
3
Insert the second vehicle key into the
ignition. Turn the ignition to the “ON”
position.
Security light will illuminate
and then turn off.
The security light will turn on solid and
then turn off. The chime will be heard
once again.
Programming is now completed.
Plug the connectors to the module and
proceed with the next step.
ON
2nd KEY
OFF
OFF
IMPORTANT: Both keys are required to complete the
programming procedure. A maximum of 5 second delay
between each step is permitted. If the delay is exceeded, the
vehicle will not allow programming to continue.
20
40
60
80
100
120
SECURITY LIGHT
ON THEN OFF
SECURITY LIGHT OFF
FLASHES
FLASHES
SOLID
THEN OFF
HOLD TO CYLINDER
JUMP THE IGNITION
12V
IGNITION
10 AMPS
1
Unplug all connectors from the module.
PLUG CONNECTORS
NOTICE:
the manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself
or to the installed device. this device must be installed by a certified technician. this guide has been written for properly trained technicians; a certain level of skill and
knowledge is therefore assumed. please review the installation guide carefully before beginning any work.
Doc. No.: ##00195##