background image

install guide

Version française disponible en ligne au www.idatalink.com

doorlock interface

chrysler / dodge / Jeep

Page 8 of 11

 

ADS-DLSL-CH1

 

20071214

 www.idatalink.com

 

For technical assistance, contact your distributor or visit www.idatalink.com/support 

© 2007 ADS Inc. 

NOTICE:

 the manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself 

or to the installed device. this device must be installed by a certified technician. this guide has been written for properly trained technicians; a certain level of skill & 

knowledge is therefore assumed. please review the installation guide carefully before beginning any work.

 www.idatalink.com

 

For technical assistance, contact your distributor or visit www.idatalink.com/support 

© 2007 ADS Inc. 

1

2

3

Locate the Immobilizer security light. It is either a round red indicator in the cluster or a red led on top of the dashboard.

Locate the transponder on the antenna.

Fold the harness as shown below.

TRANSPONDER PRE-PROGRAMMING

20

40

60

80

100

120

LOCATE 

THE SECURITY LIGHT

1

3

Wait approximately 15 seconds
for security light to flash, indicating 
you have accessed “Learning mode”.
A warning chime will also be heard.
Turn the ignition to the “OFF” position 
and remove key from ignition.

Hold the transponder to the ignition 
cylinder and power the main ignition 
using a 10 Amp fused test lead.
(Note: If you encounter power loss 
during this step, you will need to exit 
learning mode and restart transponder 
programming from step 1.

The security light will start flashing, 
indicating you are now in programming 
mode.

DO NOT INTERRUPT IGNITION until the 
security light stops flashing.

Insert the first vehicle key into the ignition. 
Turn the ignition to the “ON” position.

Security light on cluster will illuminate.

Once, the security light turns off, 
turn the ignition to the “OFF” position
and remove key from ignition cylinder.

TRANSPONDER PROGRAMMING

ON

2

Insert the second vehicle key into the 
ignition.  Turn the ignition to the “ON” 
position.

Security light will illuminate
and then turn off.

The security light will turn on solid and 
then turn off. The chime will be heard 
once again.

Transponder programming is now 
completed.

ON

2nd KEY

OFF

OFF

IMPORTANT: Both keys are required to complete the 
programming procedure. A maximum of 5 second delay 
between each step is permitted. If the delay is exceeded, the 
vehicle will not allow programming to continue.

20

40

60

80

100

120

SECURITY LIGHT

 ON THEN OFF

SECURITY LIGHT OFF

FLASHES

FLASHES

SOLID THEN OFF

HOLD TO CYLINDER

12V

IGNITION

10 AMPS

ProgrAMMINg ProCeDUre

3. program your module 

see instructions on the following pages

IMPORTANT NOTICE

Chrysler’s Immobilizer modules will accept a maximum of 4 programmed 
keys. If the vehicle already has 4 keys programmed, it will be impossible 
to  learn  the  transponder  unless  a  new  Immobilizer  module  is  installed  in 
the vehicle and programmed to recognize the vehicle ID by the new car 
dealer.
Programming will require access to TWO valid vehicle keys. These keys will 
be returned to the vehicle owner once the installation has been completed.

note:

  The  transponder  is  compatible  with  the  Chrysler  Durango  2004 

vehicle. However, all Durango’s built prior to 5/17/04 must get a WCM 
module upgrade which will correct a problem preventing the vehicle from 
learning  additional  keys.  Chrysler  is  correcting  this  issue  only  when  a 
Durango owner requests a new transponder key.
The transponder must be programmed as would an additional key.
The WCM replacement part number is 56038675AS.

Num. de Doc.: ##00130##

Summary of Contents for ADS-DLSL-CH1












Reviews: