background image

ID TECH VP5300M User Manual 

Page | 37  

 

15.

 

FCC warning statement 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any 
interference received, including interference that may cause undesired operation.  
 
The user manual for an intentional or unintentional radiator shall caution the user that changes or 
modifications not expressly approved by the party responsible for compliance could void the user’s 
authority to operate the equipment.  
 

Note:

 The grantee is not responsible for any changes or modifications not expressly approved by the 

party responsible for compliance. Such modifications could void the user’s authority to operate the 
equipment.  
 

Note:

 This equipment has been tested and found to comply with the limits for a Class B digital device, 

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates uses and can 
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause harmful 
interference to radio or television reception, which can be determined by turning the equipment off 
and on, the user is encouraged to try to correct the interference by one or more of the following 
measures: 

 

Reorient or relocate the receiving antenna.  

 

Increase the separation between the equipment and the receiver. 

 

Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected.  

 

Consult the dealer or an experienced radio/TV technician for help.  

 
This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. 
The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any 
other antenna or transmitter and must be installed to provide a separation distance of at least 20cm 
from all persons. 
 

16.

 

IC Compliance Warning 

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science 
and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following 
two conditions:  

1.

 

This device may not cause interference, and  

2.

 

This device must accept any interference, including interference that may cause undesired 
operation of the device.  

 

Summary of Contents for ViVOpay VP5300M







































Reviews: