background image

Mounting

Protege DIN rail modules are designed to mount on standard DIN rail either in dedicated DIN cabinets or on
generic DIN rail mounting strip.

When installing a DIN rail module, ensure that there is adequate clearance around all sides of the device and
that air flow to the vents of the unit is not restricted. It is recommended that you install the module in a location
that will facilitate easy access for wiring. It is also recommended that the module is installed in an electrical
room, communication equipment room, secure cabinet, or in an accessible area of the ceiling.

1.

Position the DIN rail module with the labeling in the correct orientation.

2.

Hook the mounting tabs (opposite the tab clip) under the edge of the DIN rail.

3.

Push the DIN rail module against the mount until the tab clips over the rail.

Removal

A Protege DIN rail module can be removed from the DIN rail mount using the following steps:

1.

Insert a flat blade screwdriver into the hole in the module tab clip.

2.

Lever the tab outwards and rotate the unit off the DIN rail mount.

PRT-ZX16-DIN | Protege DIN Rail 16 Input Expander | Installation Manual

9

Summary of Contents for PRT-ZX16-DIN





































Reviews: