background image

Declaration of Conformity

               Information Technology Equipment

6260 Sequence Drive

San Diego, CA 92121-4371

(800) 523-2320  

/  (858) 677-0877

The product(s) covered by this declaration:

WINCOMM4

The European Union directives covered by this declaration:

EMC Directive 89/336/EEC and Low Voltage Directive 73/23/EEC

The basis on which conformity is declared:

EN 50081-1:1992  Emissions, Generic Requirements

-EN 55022 Limits and Methods of Measurement of Radio Disturbance Characteristics of Information
Technology Equipment

EN 50082-1:1992 

 

Immunity,  Generic Requirements

-EN61000-4-2:1995 Electrostatic Discharge (ESD) Immunity
-EN61000-4-3:1995 Radiated RF Field Immunity
-EN61000-4-4:1995 EFT Immunity for AC and I/O Lines

EN 60950:1992  Safety of Information Technology Equipment

The technical documentation required to demonstrate this product meets the requirements of the EMC Directive
and the Low Voltage Directive has been compiled by ICS Advent and is available for inspection by the relevant
enforcement authorities. 

Attention

The attention of the specifier, purchaser, installer, or user is drawn to special measures and limitations for use
which must be observed when the product is taken into service to maintain compliance with the above
directives. Details of these special measures and limitations are in the product manual.

Mr. Jim Jameson
President & Chief Executive Officer

ICS Advent Europe

Ben Turner Industrial Road

Oving Road

Chichester, West Sussex

PO19 4ET, UK

Summary of Contents for WINCOMM4

















Reviews: