background image

3

Safety Information

Note:

Nearly every electronic device is susceptible to

electromagnetic interference (EMI) if inadequately
shielded, designed, or otherwise configured for
electromagnetic compatibility.
To avoid electromagnetic interference and/or
compatibility conflicts, turn off your device in any facility
where posted notices instructed you to do so. Hospitals
or health care facilities may be using equipment that is
sensitive to external RF energy.
Some devices may interfere with some hearing aids.
If you use any other personal medical devices, consult
the manufacturer of your device to determine if it is
adequately shielded from RF energy. Your physician
may be able to assist you in obtaining this information.

Use only power supply approved for use with this
particular device. The use of any other type will
invalidate the warranty and can be dangerous.
Never try to disassemble or service the equipment by
yourself.
Keep the handset and accessories out of reach from
children.
There may be restrictions on using Bluetooth technology
in some locations. These could include hospitals, petrol
stations, laboratories, potentially explosive surroundings
and etc.
The socket-outlet shall be installed near the equipment
and shall be easily accessible.

18

Symptom

Solution

Disable Bluetooth in
the iPhone and then
enable it again, the
disconnected
Bluetooth
connection between
the handset and the
iPhone cannot be
automatically
resumed.

Due to differences in each
iPhone's software, so it is
normal for some iPhone that
the Bluetooth connection
cannot be automatically
resumed. If in this case,
please establish the
Bluetooth connection
manually (See P11
"Connecting an iPhone").

Summary of Contents for i-500












Reviews: