background image

 

7

z

 

We are not liable for any problems caused by unauthorized modifications or attempted repair.

 

 

Do not allow other object falling into the device  

z

 

Please make sure there is no metal or inflammable, explosive substance in the speed dome. 

z

 

The above mentioned objects in the device may result in fire, short-circuit or damage.  

z

 

Please shut down the device and disconnect the power cable if there is water or liquid falling 

into the camera. Please contact your local retailer ASAP. 

z

 

Please pay attention to the camera. Avoid the sea water or rain to erode the camera. 

 

 

Handle carefully  

Do not allow this series product fall down to the ground.  

Avoid heavy vibration. 

 

 

Installation Environment Requirement 

z

 

This series speed dome should be installed in a cool, dry place away from direct sunlight, 

inflammable, explosive substances and etc. 

z

 

This series product shall be away from the strong electromagnetism radiant, please keep it 

away from wireless power, TV transmitter, transformer and etc. 

 

 

Daily Maintenance  

z

 

Please use the soft cloth to clean dust on the shell, or you can use soft cloth with cleaning 

liquid to clean the shell and then use soft cloth to make it dry. 

z

 

Do not use gasoline, dope thinner or other chemical material to clean the shell. It may result 

in shell transfiguration or paint flake. 

z

 

Do not allow the plastic or rubber material to touch the shell for a long time. It may result in 

paint flake. 

 

 

Summary of Contents for ICIPP3020HDIR






























Reviews: