manualshive.com logo in svg

ICRealtime ICIPP3020HDIR, Installation Manual

Share
Download
ICRealtime ICIPP3020HDIR Installation Manual Download Page 10

 

10

 

Figure 1-1 

1.2.3  Clip wall mount bracket installation  

Please connect the flange to the speed dome device. Connect the cable port of the flange to the 

slot of the speed dome one by one (It includes power, video, RS485, network cable and alarm 

input/output. Please note you can connect the network cable or the alarm input/output if 

necessary.). After you connected the flange to the speed dome, please install it to the bracket. 

Use the three inner hex screws to secure. See Figure 1-2. 

For the corner mount installation or the pole mount installation, you can also refer to these 

contents.  

 

Figure 1-2 

 

1.2.4  Address and Baud Rate Setup  

Now you can set the IR speed dome address and baud rate. The IR speed dome interface is 

shown as below. See Figure 1-3. There are two dial switches: SW1 and SW2. Here you can set 

the address, baud rate, communication protocol and etc.  Please refer to chapter 1.4 for detailed 

information.  

Summary of Contents for ICIPP3020HDIR






























Reviews:

No comments

Brands by name

Popular brands

Load more brands