background image

D300 Series Operating Manual

3

◀◀

|

Preface    

Please read this manual carefully before use.
When receiving the instrument, please open the package carefully, check whether the instrument and accessories are damaged by  

transportation and whether the accessories are complete. If any abnormalities are found, please contact our after-sales service department 

or regional customer service center, and keep the package for return processing.
This instrument is an analytical measurement and control instrument with highly precision.Only skilled,trained or authorized person should 

carry out installation, setup and operation of the instrument.Ensure that the power cable is physically separated from the power supply 

when connection or repair. Once the safety problem occurs, make sure that the power to the instrument is off and disconnected.

For example, 

1.  Apparent damage to the analyzer
2.  The analyzer does not work properly or provides specified measurements
3.  The analyzer has been stored for a long time in an environment where the temperature exceeds 70°C
The analyzer must be installed by licensed professionals in accordance with relevant local specifications, and instructions are included in 

the operation manual. Comply with the technical specifications and input requirements of the controller.

Features

The instrument is equipped with different types of pH or ORP sensors. Widely used in power plants, petrochemical industry, metallurgical 

electronics, mining, paper industry, biological fermentation engineering, medicine, food and beverage, environmental protection water 

treatment, aquaculture, modern agricultural planting and other industries. The pH (acidity and alkalinity) value, ORP (redox potential) value 

and temperature value of water solution were continuously monitored and controlled.

 

‰

Large LCD display

 

‰

Intelligent menu operation

 

‰

Automatic calibration

 

‰

automatic temperature compensation

 

‰

Two (2) relay control switches

 

‰

4-20mA & RS485

 

‰

Multi-parameter display — simultaneously shows pH, ORP and temperature

 

‰

Password protection

Summary of Contents for ProCon D300 Series





























Reviews: