background image

vi

New2001

PRECAUTIONS

R

WARNING!  NEVER

  connect  the  transceiver  to  an  AC 

outlet. This may pose a fire hazard or result in an electric shock.

R

WARNING! NEVER

 connect the transceiver to a pow-

er source of more than 16 V DC or use reverse polarity. This 
will ruin the transceiver.

R

WARNING! NEVER

 cut the DC power cable between 

the DC plug at the back of the transceiver and fuse holder. If 
an incorrect connection is made after cutting, the transceiver 
may be damaged.

CAUTION:  NEVER

  place  the  transceiver  where  normal 

operation  of  the  vessel  may  be  hindered  or  where  it  could 
cause bodily injury.

KEEP

  the  transceiver  and  microphone  at  least  1  m  away 

from the vessel’s magnetic navigation compass.

DO  NOT

  use  or  place  the  transceiver  in  areas  with  tem-

peratures below –20°C (–4°F) or above +60°C (+140°F) or, in 
areas subject to direct sunlight, such as the dashboard.

DO NOT

 use harsh solvents such as benzine or alcohol to 

clean the transceiver, as they will damage the transceiver’s 
surfaces.  If  the  transceiver  becomes  dusty  or  dirty,  wipe  it 
clean with a soft, dry cloth.

DO NOT

 disassemble or modify the transceiver for any rea-

son.

BE  CAREFUL!

 

The  transceiver  rear  panel  will  become 

hot when operating continuously for long periods of time.

Place the transceiver in a secure place to avoid inadvertent 
use by children.

BE CAREFUL! 

The transceiver and the supplied or op-

tional  HM-195 

commandmic

iv

  meet  IPX7  requirements 

for waterproof protection. However, once the transceiver has 
been dropped, waterproof protection cannot be guaranteed 
because of possible damage to the transceiver’s case or the 
waterproof seal.

*  Except  for  the  DC  power  connector,  NMEA  In/Out  leads  and  AF 

Out leads.

For U.S.A. only
CAUTION:

 Changes or modifications to this device, not ex-

pressly  approved  by  Icom  Inc.,  could  void  your  authority  to 
operate this device under FCC regulations.

Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incor-
porated (Japan) in Japan, the United States, the United Kingdom, Germany, 
France, Spain, Russia and/or other countries. 
COMMANDMIC is a registered trademark of Icom Incorporated (Japan) in Ja-
pan and the United States.

Summary of Contents for M400BB SW

























Reviews: