![background image](http://html1.mh-extra.com/html/icom/ic-f410/ic-f410_service-manual_4268802012.webp)
5-1 PREPARATION
‘
‘
REQUIRED TEST EQUIPMENT
‘
‘
ADJUSTMENT FREQUENCY DATA
Before starting the adjustment, back up the original frequen-
cy data and program adjustment frequency at right using the
optional programming software (EX-2057 Rev. 1.0 or later
for IC-F410/F420, CS-F300S for IC-F410S/F420S), cloning
cable (OPC-478) and adaptor cable (OPC-592) for your con-
venience.
‘
‘
TRIMMER ADJUSTMENT
When you adjust the contents on page 5-4, TRIMMER
ADJUSTMENT, the optional EX-2057 (or CS-F300S), OPC-
478 and JIG CABLE (See illustration at CONNECTIONS.)
are required.
• STARTING TRIMMER ADJUSTMENT
Turn the transceiver power ON, connect a computer to the [MIC] jack using the optional OPC-478 CLONING CABLE and JIG
CABLE, then start up the "ADJUST" program in EX-2057 (or CS-F300S).
•
STARTING THE PROGRAM
q
Boot up DOS.
w
Insert the EX-2057 (CS-F300S) backup disk into drive A.
e
Type the following to start up the program:
ADJ>ADJUST [/A : /B]*
1
[/1 : /2]*
2
[Enter]
• The adjustment screen appears after reading set data from
the transceiver.
r
After the adjustment screen appears, set or modify the data as
desired.
*
1
PLL reference crystal type.
/A: This does not activate for IC-F410/F410S/F420/F420S’s
adjustment.
/B: TCXO crystal type. (You must select [/B] for IC-
F410/F410S/F420/F420S’s adjustment.)
*
2
RS-232C port number.
NOTE:
When the EEPROM (FRONT unit; IC3) is replaced or the transceiver displays an error message and beeps, the
following operation is necessary before starting the ADJUSTMENT.
1. Download the programmed data using the EX-2057 or CS-F300S from an exact same version of the transceiver, then
save it. (See the instructions for detailed operation.)
2. Set the cursor to the [MODEL] and push the [
↓
] key on the computer keyboard.
3. Type "RESERVE" then push [Enter].
"Reserved" indicator flashes at the right hand, top corner on the computer screen.
4. Connect the transceiver which has been repaired, then write the data to the transceiver.
EQUIPMENT
DC power supply
RF power meter
(terminated type)
Frequency counter
FM deviation meter
DC voltmeter
GRADE AND RANGE
Output voltage
: 13.2 (13.6) V DC
Current capacity
: 15 A or more
Measuring range
: 1–50 W
Frequency range
: 300–600 MHz
Impedance
: 50
Ω
SWR
: Less than 1.2 : 1
Frequency range
: 0.1–600 MHz
Frequency accuracy : ±1 ppm or better
Sensitivity
: 100 mV or better
Frequency range
: DC–600 MHz
Measuring range
: 0 to ±10 kHz
Input impedance
: 50 k
Ω
/V DC or better
EQUIPMENT
Audio generator
Standard signal
generator (SSG)
Oscilloscope
AC millivoltmeter
External speaker
Attenuator
GRADE AND RANGE
Frequency range
: 300–3000 Hz
Measuring range
: 1–500 mV
Frequency range
: 0.1–600 MHz
Output level
: 0.1 µV–32 mV
(–127 to –17 dBm)
Frequency range
: DC–20 MHz
Measuring range
: 0.01–20 V
Measuring range
: 10 mV–10 V
Input impedance
: 4
Ω
Capacity
: 5 W or more
Power attenuation
: 50 or 60 dB
Capacity
: 50 W or more
• ADJUSTMENT FREQUENCY
∏
∏
: IC-F410/F410S (PMR),
Ò
Ò
: IC-F420/F420S (LMR)
L: L-band, ML: ML-band, MH: MH-band, H: H-band
SECTION 5
ADJUSTMENT PROCEDURES
5 - 1
A:\>CD ADJ
Boot up DOS,
and change the
directory.
Program starts up,
then the adjust-
ment screen
appears after read-
ing set data from
the transceiver.
A:\>ADJ>ADJUST [/B] [/1]
Memory CH
: 1
Power(Hi) : 174
‘ ‘ ‘ ‘ ‘ ‘ ‘ ‘ ‘ ‘ ‘
– – – – – – – – –
Power(L2) : 88
‘ ‘ ‘ ‘ ‘ ‘ ‘
– – – – – – – – – – – – – –
Power(L1) : 44
‘ ‘ ‘
– – – – – – – – – – – – – – – – – – –
M O D N
: 68
‘ ‘ ‘ ‘ ‘
– – – – – – – – – – – – – – – – –
M O D W : 137
‘ ‘ ‘ ‘ ‘ ‘ ‘ ‘ ‘ ‘ ‘
– – – – – – – – –
DTCS N : 24
‘ ‘
– – – – – – – – – – – – – – – – – – – –
DTCS W : 51
‘ ‘ ‘ ‘
– – – – – – – – – – – – – – – – – –
TXF SET
:
BPF T1
: 40
‘ ‘ ‘ ‘ ‘
– – – – – – – – – – – – – – – – –
BPF T2
: - 9
‘ ‘ ‘ ‘ –
– – – – – – – – – – – – – – – – –
BPF T3
: -17
‘ ‘ ‘ ‘ –
– – – – – – – – – – – – – – – – –
BPF T4
: -15
‘ ‘ ‘ ‘ ‘
– – – – – – – – – – – – – – – – –
AF Vol.L
: 1
– – – – – – –– – – – – – – – – – – – – – – –
S Q L
: 10
‘ ‘
– – – – – – – – – – – – – – – – – – – –
∗∗∗∗∗
Trimmer Control Software for IC–F300 Series
∗∗∗∗∗
Rev. 1.0
A/D VIN 165 : A5h
13.23V
A/D TEMPS 173 : ADh
24.81'C
A/D LVIN 47 : 2Fh
0.92V
A/D SD 38 : 26h
0.75V
D/A DTCS BL 149 : 95h
58.43%
D/A SQL Lev 0 : 00h
0.00%
D/A BP T1 98 : 62h
2.03V
D/A BP T2 49 : 31h
1.41V
D/A BP T3 41 : 29h
1.31V
D/A T4/POW 43 : 2Bh
1.34V
D/A REF 147: 93h
2.40V
D/A AF/Dev 0 : 00h
0.00%
RX:440.20000MHz TX:440.10000MHz
MODE: Wide
POW: High
[Space]: A/D, D/A Read
[TAB]: Display Parameters [F8] at BPF: Sweep [F9] at BPF T1: Sweep T1~T4
[Enter] at TXF: REF Set Mode
↑
/
↓
: Cursor Up/Down < / > : –/+ ESC : Quit
Startup command.
,
,,,
,,,,
,,,,
,,,,
,,,,
,,,
,
Channel
Frequency [MHz]
Power
No.
L
∏
∏
ML
Ò
Ò
ML
MH
∏
∏
H
Ò
Ò
H selection
1
400.0 440.0 450.0 470.0
490.0
Low1
2
430.0
470.0
490.0 520.0 512.0
Low1
3
400.0 440.0 450.0 470.0
490.0
Low2
4
400.0 440.0 450.0 470.0
490.0
High