![background image](http://html.mh-extra.com/html/icom/ic-7410/ic-7410_instruction-manual_612268096.webp)
89
SET MODE
10
USB Audio SQL
38.
(Default: OFF(OPEN))
Select whether or not to output the audio from the
[USB] connector on the rear panel, according to the
squelch state.
The same audio signals are sent from the [USB] con-
nector and the [ACC] sockets.
- The beep tones and the voice synthesizer announce-
ments are not sent.
- The received audio output level cannot be adjusted
with the [AF] control.
• OFF (OPEN) : The received audio is always sent,
regardless of the squelch state.
• ON
: The received audio is sent when the
squelch is open.
USB MOD Level
39.
(Default: 50%)
Set the input modulation level of the [USB] connector
to between 0% and 100% in 1% steps.
DATA OFF MOD
40.
(Default: MIC,ACC)
Select the desired connector(s) for data modulation
input in the data OFF mode.
• MIC
: Use the signals from [MIC].
• ACC
: Use the signals from [ACC] (pin 11).
• MIC, ACC : Use the signals from [MIC] and [ACC]
(pin 11).
• USB
: Use the signals from [USB].
DATA MOD
41.
(Default: ACC)
Select the desired connector(s) for data modulation
input in the data mode.
• MIC
: Use the signals from [MIC].
• ACC
: Use the signals from [ACC] (pin 11).
• MIC, ACC : Use the signals from [MIC] and [ACC]
(pin 11).
• USB
: Use the signals from [USB].
CI-V Baud Rate
42.
(Default: Auto)
Set the CI-V data transfer rate between 300, 1200,
4800, 9600, 19200 bps and “Auto.”
When “Auto” is selected, the baud rate is automatically
set according to the data rate of the connected con-
troller.
CI-V Address
43.
(Default: 80h)
To distinguish equipment, each CI-V transceiver has
its own Icom standard address in hexadecimal code.
The IC-7410’s address is 80h.
When 2 or more IC-7410’s are connected to an op-
tional CT-17
ci
-
v
level converter, rotate [DIAL] to se-
lect a different address for each IC-7410; the range is
01h to DFh.
CI-V Transceive
44.
(Default: ON)
Turn the transceive operation using the CI-V system
ON or OFF.
When this item is set to ON, changing the frequency,
operating mode, etc. on the IC-7410 automatically
changes those settings on other Icom HF transceivers
or receivers, and vice versa.
• OFF : Transceive operation OFF
• ON : Transceive operation ON
USB Serial Func
45.
(Default: CI-V)
Select the function for the USB port on the rear panel.
• CI-V : Used to send CI-V commands
.
• RTTY : In the RTTY mode, used to send RTTY de
-
coded signal.
RTTY Decode Baud
46.
(Default: 9600)
Set the RTTY decode monitor speed to 300, 1200,
4800, 9600 or 19200 bps.
Calibration Marker
47.
(Default: OFF)
Use as a simple frequency check of the transceiver.
See page 98 for calibration procedure.
NOTE:
Turn OFF the calibration marker after check-
ing the frequency of the transceiver.
• OFF : Calibration marker OFF
• ON : Calibration marker ON
REF Adjust
48.
During frequency calibration, set the internal refer-
ence frequency to between 0% and 100% range in 1%
steps.
NOTE:
The default setting is different for each
transceiver.
■
Set mode description (Continued)