background image

2

SET MODE

5

 

D

Roger Beep

You can turn ON the Roger Beep function to beep to 
indicate that the transmission has ended.

 

D

Ringer Level

You can set the Ringer Level to between 1 and 5, or 1 
(Linked) and 5 (Linked). 
When a linked level is set, you can adjust the Ringer 
Level by rotating [VOL].

  

NOTE

: You need to set the Beep function to ON 

before setting the Ringer Level. (p. 4)

Ringer Level 3 (default)

Ringer Level 5

Ringer Level 3 (Linked)

Ringer Level 5 (Linked)

 

D

Squelch Level

The Squelch circuit eliminates background noise when 
no signals are present. 
Set the level to where the noise just disappears, for 
proper operation. 
A higher level is better for inner cities or noisy areas, 
and a lower level is more beneficial in quiet, rural or 
country areas. (0=lowest, 9=highest)

Squelch Level 3 (default)

Squelch Level 0

 

D

Mic Gain

You can adjust the microphone sensitivity to between 
1 (minimum sensitivity) and 4 (maximum sensitivity). 
With a higher sensitivity, the microphone picks up 
softer voices, though it may pick up more ambient 
noise.

Mic Gain

sensitivity 2 (default)

Mic Gain sensitivity 1

Roger Beep OFF (default)

Roger Beep ON

 

D

Battery Voltage

You can set to display the Battery Voltage for 2  
seconds, when you turn ON the transceiver.

Battery Voltage

OFF (default)

Battery Voltage ON

 

D

Signal Monitor

You can select whether or not to mute a Selcall code 
signal, DTMF code signal or Roger Beep emission. 

ON: Unmuted
OFF: Muted

Signal Monitor ON (default)

Signal Monitor OFF

 

D

Auto Power OFF

You can set the transceiver to automatically turn OFF 
after a set period without any key opertion. 
You can set it to between 0.5 and 4.0 hours (0.5 hour 
steps) or 8.0 hours.

Auto Power OFF 

is OFF (default)

2 hour setting

 

D

Power Save

The Power Save function reduces the current drain by 
deactivating the receiver circuit if a signal is not received, 
or the transceiver is not used for 5 seconds. 
The receiver periodically reactivates, checks for any 
signals, and deactivates according to a preset timer 
setting.

Power Save ON (default)

Power Save OFF

Summary of Contents for IC-41PRO






















Reviews: