Icidu MR0-WR541G User Manual Download Page 54

Page: 54 / 77

MR0-WR541G

54M Wireless Router User Guide

Figure 5-40 Advanced Security settings

Packets Statistic interval (5 ~ 60) -

The default value is 10. Select a value

between 5 and 60 seconds in the pull-down list. The

Packets Statistic interval

value indicates the time section of the packets statistic. The result of the statistic
used for analysis by

SYN Flood

UDP Flood

and

ICMP-Flood

DoS protection -

Enable

Disable

the DoS protection function. Only when it is

enabled, will the flood filters be effective.

Enable ICMP-FLOOD Attack Filtering -

Enable

Disable

the

ICMP-FLOOD

Attack Filtering.

ICMP-FLOOD Packets threshold: (5 ~ 3600) -

The default value is 50. Enter a

value between 5 ~ 3600 packets. When the current

ICMP-FLOOD

Packets

numbers is beyond the set value, the router will start up the blocking function
immediately.

Enable UDP-FLOOD Filtering -

Enable

Disable

the

UDP-FLOOD

Filtering.

UDP-FLOOD Packets threshold: (5 ~ 3600) -

The default value is 50. Enter a

value between 5 ~ 3600 packets. When the current

UPD-FLOOD

Packets numbers

is beyond the set value, the router will start up the blocking function immediately.

Enable TCP-SYN-FLOOD Attack Filtering - Enable

Disable

the

TCP-SYN-

FLOOD

Attack Filtering.

TCP-SYN-FLOOD Packets threshold: (5 ~ 3600) -

The default value is 50. Enter

a value between 5 ~ 3600 packets. When the current

TCP-SYN-FLOOD

Packets

numbers is beyond the set value, the router will start up the blocking function
immediately.

Ignore Ping Packet from WAN Port

Enable

Disable

ignore ping packet from

Summary of Contents for MR0-WR541G














































































Search results

Summary of Contents for MR0-WR541G

Reviews:

Related manuals for MR0-WR541G

Brands by name

Popular brands

Icidu MR0-WR541G, User Manual

Search results

Summary of Contents for MR0-WR541G

Reviews:

Related manuals for MR0-WR541G

Brands by name

Popular brands