Icidu MR0-WR541G User Manual Download Page 21

Page: 21 / 77

MR0-WR541G

54M Wireless Router User Guide

Static IP

. If you are given a user name and a password, please select the type of your

ISP provided(PPPoE/BigPond/L2TP/PPTP)

If you are not sure which connection type

you use currently, please contact your ISP to obtain the correct information.

1. If

you

choose

Dynamic IP,

the router will automatically get IP parameters from

your ISP. You can see the page as follows (figure 5-4):

Figure 5-4

WAN – Dynamic IP

This page displays the WAN IP parameters assigned dynamically by your ISP,
including IP address, Subnet Mask, Default Gateway, etc. Click the

Renew

button to

renew the IP parameters from your ISP. Click the

Release

button to release the IP

parameters.

MTU Size -

The normal MTU (Maximum Transmission Unit) value for most Ethernet

networks is 1500 Bytes. For some ISPs you need to reduce the MTU. But this is
rarely required, and should not be done unless you are sure it is necessary for your
ISP connection.

If your ISP gives you one or two DNS addresses, select

Use These DNS Servers

and enter the primary and secondary addresses into the correct fields. Otherwise,
the DNS servers will be assigned dynamically from your ISP.

Note:

If you get address and find error when you go to a Web site, it is likely that

your DNS servers are set up improperly. You should contact your ISP to get DNS
server addresses.

Get IP with Unicast DHCP -

A few ISPs' DHCP servers do not support the

broadcast applications. If you cannot get the IP Address normally, you can choose

Summary of Contents for MR0-WR541G














































































Search results

Summary of Contents for MR0-WR541G

Reviews:

Related manuals for MR0-WR541G

Brands by name

Popular brands

Icidu MR0-WR541G, User Manual

Search results

Summary of Contents for MR0-WR541G

Reviews:

Related manuals for MR0-WR541G

Brands by name

Popular brands