background image

Installation

11

Installation

PRODUCT RECEIPT

Each phase of the appliance installation must be carried out by 

Qualified Personnel

wearing appropriate Personal Protective 

Equipment (PPE)

, in compliance with the national and local Laws in force.

An incorrect installation of the appliance or the failure to use PPE can cause severe damage to persons or property for which the 
Manufacturer DECLINES ANY RESPONSIBILITY.

 

CODEX GT

 Boilers are supplied in six packages, indicated below, positioned on one pallet:

 

BOILER BODY (1)

 

thermally insulating mineral wool 

MATS (2)

 and fastening springs

 

SLAT SUPPORT KIT (3)

 

SLATS (4)

 

CONTROL PANEL (5)

 

BURNER (6)

5

3

2

4

6

1

IMPORTANT

Upon receipt of 

CODEX GT

 Boiler, make sure that the supply is intact and undamaged and promptly contact 

ICI 

CALDAIE S.p.A.

 if it does not correspond to the order

IMPORTANT

The instruction manual is an integral part of the appliance and it MUST be carefully read before installing and 
commissioning the Boiler, carefully stored for further consultations and it MUST always accompany Boiler.

IMPORTANT

PACKAGING:

 as for packages, 

ICI CALDAIE S.p.A.

 complies with the specific recycling systems of each country, ensuring 

an optimal reuse of them. All the materials used for the packaging respect the environment and can be recycled, such 
as wood, plastic, cardboard.

Cooke Industries - Phone: +64 9 579 2185    Email: [email protected]    Web: www.cookeindustries.co.nz

Summary of Contents for 17010195

































Reviews: