background image

Proper Installation

IM-Series

5

Installation,  Start Up, and Check

Please double check these items before install & start-up before calling for service. 

(These items are not covered under your Labor Warranty)

1.

Has all tape and packing materials been removed from Machine?

2.

Is the unit installed in a location that is away from heat generating equipment  or direct sunlight?

3.

Is the unit level front to back and side to side? Adjustable  legs on the unit makes this quick and easy.

4.

Is the correct electrical power provided?  Ensure the unit has the specified voltage and amperage and is on a dedicated circuit. Do not use a
drop cord or power strip with any ice machine. This could cause a voltage drop and compensatory amperage spike or cause the circuit 
breaker to trip.

5.

Check drain line pipe sizes. Insure  they are ¾ inch and line drops ¼ inch per foot of run to insure both machine  and bin  drainage is 
effective.

6.

Is water supplied to the unit?  Water Line size, 3/8 inch, must be supplied to ensure sufficient water flow is always available. Required 
water pressure  is 20 psi minimum and 80 psi maximum.   This unit is designed to work with water temperatures  of 50

°F - 90°F.

7.

Is the unit installed in an area with sufficient ventilation at the front for proper rejection of condenser heat?  

Fresh air is taken in from  the 

and dispelled from the front.  Never block the front air vents!

8.

This unit is designed to work in ambient air temperatures  of 50

°F - 100°F.

9.

Is the Unit located in an area which has air borne particulate (flour, yeast, etc) that can build mold and bacteria inside the machine or clog
the filter and condenser? There are products that can be installed to help these problems.

10.

Scale or Mold build-up can affect the sequence of operation, timing  and production. Is  a water filter installed? We recommend  our 
exclusive  Citryne Pro Ice  Filtration for the best scale clean results. Scale will increase operating costs and reduce or shut  down the
machine’s performance.

11.

Do not install this unit outdoors.

Summary of Contents for IC Series






































Reviews: