manualshive.com logo in svg

ICE AIR ccHPWH Series, Installation And Maintenance Manual

Share
Download
ICE AIR ccHPWH Series Installation And Maintenance Manual Download Page 31

28 

 

3.3. Main interface 

 

                                                                   

       

【

2

】

↑

           

【

3

】

↑

   

               

Standby

 

 

     

Refrigeration 

    12:20 

Lock automatically 

within one 

minute   

                  Standby 

 

     

 

Refrigeration

     

Inquiry

 

 

 

 

↓

【

1

】

             

↓

【

4

】

 

 

Description:     

【

1

】

Current operation mode of the unit. 

【

2

】

The current control temperature of the unit. 

【

3

】

Indicates the status of the unit and the timing status of the unit. 

【

4

】

Indicates fault inquiry of the unit. 

 

 

3.4. Fault inquiry 

When faults occur, the main interface will note the fault. Press the <Enter> key to view the fault. 

       

   

【

1

】

↑

 

 

【

4

】

↑

       

                  Standby 

 

 

 

     

Cool                  Inquiry

   

<enter>

———→

←———

<function>

   

System unit:34 No. 

System evap. Out T         

▼ 

 

Return

                  Reset

 

<enter>

———→   

                    Standby 

 

 

 

     

Cool                         

12:20

 

 

 

                     

 

↓

【

2

】

                         

↓

【

3

】

 

 

 

Description:     

【

1

】

Indicates the fault code of the selected item and the corresponding information. Please refer to the 

instruction  book  of control  panel  for  fault  code  descriptions.  Press  <Up>  or  <Down>  key  to switch 

display of fault module or fault number:

   

System unit: indicated whole system (main unit) faults 

**No unit: indicated module faults   

** No.: faults number. 

00#~04#: circuit number         

【

2

】

Indicates to press <Function> key to return to menu of previous level.   

【

3

】

Indicates to press <Enter> key to reset fault. Display indicates to return to the main interface if there 

is no fault at present. If there is any fault, it continues to display the current fault.   

【

4

】

Indicate there is no fault after pressing <Enter> key. Then it returns to the main interface.   

 

 

 

 

Summary of Contents for ccHPWH Series



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands