IBM System Storage DCS Series Installation And Migration Manual Download Page 85

Page: 85 / 90

Index

accessible documentation 65
add

new hard disk drives 13
storage enclosures 25
used hard disk drives 14

adding hard drives, considerations 25
additional storage enclosures

cabling 38
inserting drives 38

AppWare 4
array

cannot bring online 19
configuration data for drives

incomplete 19

arrays, migrating 21
attention 19, 26, 29
attention notices x

backup

logical drives 16, 28
storage subsystem data 1

BootWare 4
bottom of drive loop, connect storage

enclosures 31

cable

trace connections 29

cabling, storage enclosure 31
cannot bring array online 19
catastrophic failure 21
caution statements x
change Fibre Channel speed settings 12
Class A electronic emission notice 66
configuration behavior, redeployed

storage subsystem 54

configuration data 15
considerations, upgrade 41
contamination, particulate and

gaseous 65

controller

drive loop LED 29
firmware level 2

by machine type 4
by model number 4
by NVSRAM version 4
current 4

firmware, verify level 1, 4, 16

controller firmware 4

upgrading 6

customize storage partitioning

information 16

danger statements x
DCS ix
documentation

websites 58

documentation format 65
documentation, using 57
drive ID and model, determining 9
drive loop

optimal state 11
speed change procedure 12

drive migration

prerequisites 1
settings

re-enable 14

drive migration enable settings

verifying 30

drive migration limitations 7
drive migration settings, verifying 17
drive/loop channel 33
drives

CRU assembly 18
do not appear marked as Failed 19
do not display 19
will not spin up 13

drives, removing 18
DS Storage Manager

publications ix

DS Storage Manager publications ix
DS3000 ix
DS4000 ix
DS4000 Storage Subsystem

firmware 4
NVSRAM 4
profile 1

DS4000 support

Web site 4

DS4300

enclosure IDs 27
Storage Subsystem firmware and

NVSRAM 4

Turbo Storage Subsystem firmware

and NVSRAM 4

DS4400 Storage Subsystem firmware and

NVSRAM 4

DS4500 Storage Subsystem firmware and

NVSRAM 4

DS5000 ix
DS5000 Storage Subsystem

firmware 4
NVSRAM 4

DS5000 support

Web site 4

electronic emission Class A notice 66
electrostatic discharge (ESD) bags 19
electrostatic discharge (ESD)

procedure 13

electrostatic discharge procedure 14
Empty Drive icon 19
end of drive loop, connect storage

enclosures 31

errors

loss of ESM path redundancy 29

ESD procedures 14
ESM Fault LED 29
ESM firmware

EXP500 4
EXP700 4
upgrade during I/O 4
upgrading 6
version, current 4

event logs, interpreting 11
EXP500

ESM firmware 4
ID switch location 27, 30

EXP700

ESM firmware 4
ID switch location 27, 30

export drives 3
exporting drives 17

Failed icons 19
FAStT200

enclosure IDs 27
HA Storage Server firmware and

NVSRAM 4

Storage Subsystem firmware and

NVSRAM 4

FAStT500 RAID controller firmware and

NVSRAM 4

FCC Class A notice 66
Fibre Channel

insert drives 13, 14, 19, 27, 38
trace cable connections 29

fire suppression 59
firmware

compatibility 4
controller 4
controller and NVSRAM levels 16
controller, NVSRAM, and ESM

levels 1

current 4
ESM, version by storage enclosure 4
updates 4

firmware and NVSRAM

DS4300

Storage Subsystem 4
Turbo Storage Subsystem 4

DS4400 Storage Subsystem 4
DS4500 Storage Subsystem 4
FAStT200

HA Storage Subsystem 4
Storage Subsystem 4

FAStT500 RAID controller 4

FlashCopy

delete 16

Summary of Contents for System Storage DCS Series



























































































Search results

Summary of Contents for System Storage DCS Series

Reviews:

Related manuals for System Storage DCS Series

Brands by name

Popular brands

IBM System Storage DCS Series, Installation And Migration Manual

Search results

Summary of Contents for System Storage DCS Series

Reviews:

Related manuals for System Storage DCS Series

Brands by name

Popular brands