IBM IBM-3415, Installation And Operating Manual

Page: 21 / 24

No dial tone/phone will not dial out.
• Check that you have plugged the AC power adapter into a working AC power outlet.
• Confirm that the AC power adapter is plugged into the DC jack on the base of the unit.
• Confirm the CHARGE/IN USE LED is lit.
• Check all telephone cord connections or try another wall jack.
Can’t hear the ring signal.
• Check the ringer ON/OFF control on the handset to make sure it is in the ON position.
While on a call, you hear another call on the line or experience radio frequency
interference.
• Switch channels for a clearer channel.
• Check the wiring for bad connections.
Can't receive or make phone calls.
• Check to be sure the phone is set to the correct type of service, either Tone or Pulse.
20
TROUBLESHOOTING
IBM-3415 PARTS CHECKLIST
1 2 3
4 5 6
7 8 9
0 #
OPER
WXYZ TUV PQRS
MNO JKL GHI
DEF ABC
IN USE
VOLUME
REDIAL FLASH
TONE
CHARGE/
IN USE
1. Handset 2. Base
4. DC power adapter
10. Quick Start Guide
8. Short line cord
for wall installation
6. Ni-Cd Battery Pack
3.6 volt Ni Cd Battery
7. 7-foot line cord
for desk use
QUICK START GUIDE
®
B A S E
P E D E S TA L
LINE 1/2 LINE 2
9V DC
SETTING UP THE BASE
1. Connect the telephone line cord to the
"Line1 / 2" and "Line2" jacks and to the
telephone outlets.
2. Use the "Line1 /2" jack if you are con-
necting only one phone line.
3. Connect the AC power adapter to
the (9V DC) jack and to an AC outlet.
The POWER lamp on the base will
glow green.
4. Raise the antenna vertically.
3.
6 volt N
i C
d Ba
ttery
INSTALL THE BATTERY
1. Slide open the battery door.
2. Plug the battery terminal together.
3. Insert the battery into the battery
compartment.
4. Place the handset on the base and allow
to charge for 12 hours.
MAKING CALLS
1. Pick up the handset from the base.
2. Press
B
or
C
.
3. Dial the number you wish to dial.
4. When you are finished talking, press the B or C keys depending on
which line is active or place the handset back into the base to end the call
IBM-3150
BASE
P E D E S TA L
Use only with class 2
Power Source 300mA
P/T DC-9V TEL LINE
1. Insert the pedestal into the slots on the bottom
of the base and slide up to lock in place. The
pedestal is reversible for desk or wall mounting.
2. Connect the telephone line cord to the
"TEL LINE" jack and to a telephone outlet.
3. Connect the AC power adapter to the 9V DC
jack and to an AC outlet.
4. Raise the antenna vertically.
CONNECTING THE PHONE TO THE WALL JACK
3
.6 v o
lt N i
C d B
a tt e ry
1. Slide open the battery door.
2. Plug the battery terminal together.
3. Insert the battery into the battery compartment.
4. Place the handset on the base and allow to
charge for 12 hours.
1. Pick up the handset from the base.
2. Press P . The LED on the base will flash while the handset is scanning
for a clear channel. The LED will glow steadily when the connection is
made. Wait until you hear a dial tone.
3. Dial the number you wish to dial.
4. When you are finished talking, press the P key or place the unit back
into the base to end the call.
Note: The “CHARGE/IN USE” light on the base will turn green when
the line is active.
IBM-3415
5. Belt-Clip
5
3. Reversible pedestal
9. 10-number
memory sticker