manualshive.com logo in svg

IBM Deskstar 40GV, Installation And Reference Manual

Share
Download
IBM Deskstar 40GV Installation And Reference Manual Download Page 5

1 

Introduction 

           

This manual was prepared to aid you in the installation of your new IBM Desk star hard disk drive.  
Installation instructions are provided for the following model numbers: 
 

• 

IC35L020AVER07  (20 GB) 

• 

IC35L040AVER07  (40 GB) 

• 

IC35L060AVER07  (60 GB) 

• 

DTLA-307075   (75 GB) 

 
 
The IBM Deskstar drive models listed above support Ultra ATA/100 and are backwards com-
patible with lower bus speeds, allowing it to obtain interface transfer rates of up to 100 MB per 
second.  Your drive will function at the maximum speed supported by your system components.   

Ultra ATA/100 performance requires the following components:  

• 

A 40-pin, 80-conductor ATA/IDE cable 

• 

A controller card or motherboard chipset with Ultra ATA/100 or higher capability 

• 

An Ultra ATA/100-compatible BIOS  

 
The IBM Deskstar drives listed above also support the following interface data transfer rates: 
 

ATA Mode 5 

 

 

 100 MB per second 

ATA Mode 4 

 

 

66.6 MB per second 

ATA Mode 2 

 

 

33.3 MB per second 

Multi-word DMA Mode 2  

16.6 MB per second 

Advanced PIO Mode 4   

16.6 MB per second 

 
The Frequently Asked Questions (FAQ) section of this manual contains further information on 
Ultra ATA/100 and Ultra ATA/66. 

Summary of Contents for Deskstar 40GV



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands