manualshive.com logo in svg

IBM Deskstar 40GV, Installation And Reference Manual

Share
Download
IBM Deskstar 40GV Installation And Reference Manual Download Page 2

ii 

Technical 

support 

          

Troubleshooting and Frequently Asked Questions (FAQ) sections are provided in the Appendix of 
this manual to aid you in the installation of your IBM Deskstar.  If the answer to your installation 
question is not found in this manual, call technical support.  Before calling, please gather as much 
of the following information as possible: 
 

• 

IBM drive model number, part number, and serial number 

• 

Operating system 

• 

BIOS manufacturer, version, and date 

• 

Any error codes and when they occurred 

• 

System type and manufacturer 

• 

Motherboard manufacturer 

• 

Chipset manufacturer 

• 

Adapter card manufacturer 

• 

Other devices in systems 

• 

Bus/cable layout (location of device, which device is at the end) 

• 

Applications used (if relevant) 

 
 
In North America 
Web 

www.ibm.com/harddrive

 

Voice  888.IBM.5214 or 507.286.5825 
Fax 507.253.DRIVE 
e-mail 

[email protected]

 

 
In the United Kingdom 
Voice 44.0870.010.2866 
e-mail 

[email protected]

 

 
In Singapore 
Voice  65.1800.840.9292 or 65.841.2900 
e-mail 

[email protected]

 

 
In Germany 
Voice 49.07032.153050 
e-mail 

[email protected]

 

 

Summary of Contents for Deskstar 40GV



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands