manualshive.com logo in svg

IBM 000E9283, Handbook

Share
Download
IBM 000E9283 Handbook Download Page 209

v

FC EN17: PCIe3 4-port 10 GbE SFP+ Copper Adapter

v

FC EN18: PCIe3 LPX 4-port 10 GbE SFP+ Copper Adapter

The PCIe3 4-port 10 GbE SFP+ Copper Adapter is a PCI Express (PCIe) generation 3, x8, short
form-factor adapter. The adapter provides four 10 Gb small form-factor pluggable (SFP+) ports into
which copper twinax transceivers will be placed. See Figure 87 on page 194. Active Copper twinax cables
up to 5 meter in length are supported such as provided by feature codes EN01, EN02 or EN03. A
transceiver is included with these cables. See “Cables” on page 194 for details. The adapter supports the
Ethernet network interface controller (NIC) function and also provides SR-IOV NIC support. SR-IOV
capability for the NIC function is supported with the appropriate firmware and operating system level
for any of the four ports. Enabling the SR-IOV function requires an HMC.

The adapter provides the following features:

v

Four 10 Gb ports that can function in the NIC mode

v

AIX Network Installation Management (NIM) support

v

The adapter supports interrupt moderation to deliver increased performance while significantly
reducing processor utilization

v

The adapter supports multiple media-access control (MAC) per interface.

v

The adapter supports integrated media-access control (MAC) and physical layer (PHY).

v

The adapter supports the following standards for the different ports and functions:
– IEEE 802.3ae in the 10 GbE ports
– 802.3ab in the 1 GbE ports
– Ether II and IEEE 802.3 for encapsulated frames
– 802.1p for setting up priority levels in tagged VLAN frames
– 802.1Q for VLAN tagging
– 802.3x for flow control
– 802.3ad for load-balancing and failover
– IEEE 802.3ad and 802.3 for link aggregation

v

The adapter provides message signal interrupts (MSI), MSI-X, and support of legacy pin interrupts.

v

The adapter supports jumbo frames up to 9.6 KB.

v

The adapter supports TCP checksum offload transmission control protocol (TCP), user datagram
protocol (UDP), TCP segmentation Offload (TSO) for IPv4 and IPv6.

v

Supports TCP segmentation or large send offload

v

Supports EEPROM-SPI and single EEPROM

v

Compliant with European Union Directive 2002/95/EC on the Restriction of the Use of Certain
Hazardous Substances in Electrical and Electronic Equipment

Managing PCIe adapters

193

Summary of Contents for 000E9283



































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands