background image

4

We  have  adjusted 

the 

TE-HUD according to the general test  values 

at  the  factory,  if  you  find  TE-HUD  display  information  is  different 
from  dashboard,  then  make  the  following adjustments: 

1.

 

Long press the wave button vertically for 5s

Entering

 into  the  setting  mode,  there  are  three  button  for wave 

button:  Up

 

button  (turning  the  button  to  upside),  OK  button 

(pressing  the  button  vertically),

 

Down  button  (turning  the  button  to 

downside),  after  enter  into  the  setting  mode,

 

press  the  OK  button 

vertically  one  time,  the  menu  will  increase  one.  Turning

 

the  upside 

button  or  downside  button  to  increase  or  decrease  the  parameter.

 

After  finish  the  adjustment,  long  press  the  wave  button  vertically 
for  5s  to

 

return  to  the  display interface.

Menu  Function  Adjustmen

t range  

Description 

Factory 

preset 

number 

Picture show 

Speed 

50-150 If TE-HUD speed 

is higher than 
dashboard 
instrument, low 
this number (by 
push down 
function setting 
button), normally 
low by 2 one time, 
then check if it is 
the same as car 
instrument. For 
speed lower than 
instrument, push 
up, do the same.  

107 

Engine 

RPM 

50-150 Start your car, shift 

to ‘P’, and do 
adjustment (push 
function button 
down for decrease  
and up for 
increase ) 

117 

RPM 

Alarm 

0-75

Factory preset 
Alarm is 7000 
RPM. You can 
adjust it by push 
function button up/
down.  

70 

Summary of Contents for TE-HUD













Reviews: