manualshive.com logo in svg

IBASE Technology IB936, User Manual, Page: 27 / 66

Share
Download
IBASE Technology IB936 User Manual Download Page 27

BIOS SETUP 

                         IB936 User’s Manual 

23 

 

BIOS Setup 

 

This chapter describes the different settings available in the Award BIOS 
that  comes  with  the  board.  The  topics  covered  in  this  chapter  are  as 
follows: 
 
BIOS Introduction ............................................................................... 24 
BIOS Setup .......................................................................................... 24 
Standard CMOS Setup ......................................................................... 26 
Advanced BIOS Features..................................................................... 29 
Advanced Chipset Features.................................................................. 32 
Power Management Setup ................................................................... 38 
PNP/PCI Configurations ...................................................................... 41 
PC Health Status .................................................................................. 42 
Frequency/Voltage Control .................................................................. 43 
Load Fail-Safe Defaults ....................................................................... 44 
Load Optimized Defaults ..................................................................... 44 
Set Supervisor Password ...................................................................... 44 
Save & Exit Setup ................................................................................ 44 
Exit Without Saving............................................................................. 44 

Summary of Contents for IB936



































































Reviews:

No comments