All 2 pickups models : Pickup Balancer
The pickup balance control pot allows the user to blend
between the front and back pickups using a single pot. The
center position of the pot has a de-tent which will set both
pickups to equal output. Turning the knob clockwise increases the neck pickup
while decreasing the output of the bridge pickup. Turning the knob counter
clockwise decreases the neck pickup and increases the output of the bridge
pickup.
BRIDGE
PICKUP
NECK
PICKUP
bass Electronics
Bass Controls
Volume
Bass Boost/Cut
Mid Boost/Cut
Balancer
Treble Boost/Cut
EDB with EQB III
Tone
Front Pickup
Volume
Rear Pickup Volume
Phat EQ.
EDB with PHAT
Tone
Front Pickup
Volume
Rear Pickup Volume
Phat II EQ.
GSR with PHAT II
Volume
Balancer
Mid Boost/Cut
Mid Frequency
Treble Boost/Cut
Bass Boost/Cut
K5 with VARI-MID III
Volume
Balancer
Treble Boost/Cut
Bass Boost/Cut
BTB with EQB IIB
Volume
Balancer
Treble Boost / Cut
Bass Boost / Cut
SRX with EQB IIDX
Volume
Bass
Boost/Cut
Treble Boost/Cut
Balancer
SR with EQB IIC
Bass Bridges
B100, B105, B106 Bridge
SR, SRX, RD, BTB, GWB35
The B100, B105 and B106 bass bridges were
designed for easy string change. The strings
are installed by hooking the ball end into the
string catch at the rear of the bridge. The
intonation can be adjusted by moving the
saddle forward or backward using a Phillips
head (+) screwdriver on the adjustment
screw at the rear of the bridge. String height
is controlled by using a 1.5mm Allen wrench to raise or lower the Allen screws on
either side of the saddle.
B10, B15 Bridge
SR, GSR, ICB, GAXB
To replace strings, thread the new strings
through the string holes located on the back of
the tailpiece and bring them up and over the
saddle. The intonation can be adjusted by
moving the saddle forward or backward using
a Phillips head (+) screwdriver on the
adjustment screw at the rear of the bridge. String height is controlled by using a
1.5mm Allen wrench to raise or lower the Allen screws on either side of the saddle.
ACCU-CAST B200/B205
SRX, DWB3, RD
REPLACING THE STRINGS
The Accu-Cast B200 and B205 bass bridges
allow two styles of string installation. The
strings are installed by lowering the ball end
into the bridge and hooking the ball end
below the string catch at the rear of the
bridge. (Figure 1)
In this method, the strings are installed by
lowering the ball end into the bridge and
holing the string catch directly below the
saddle. This increases string tension and
adds sustain. (Figure 2)
STRING HEIGHT
To raise or lower the string action, insert the
correct Allen wrench into the screw (A) at the
saddle. To raise the saddle turn the wrench
clockwise and to lower the saddle turn the
wrench counter clockwise.
INTONATION
Intonation adjustment can be made by adjusting the intonation screws (B) at the
rear of the bridge clockwise to move the saddle back and counter clockwise to
move the saddle forward.
ACCU-CAST B20/B25
SR,
The Accu-Cast bass bridge was designed for
easy string change, durability, and accurate
string height adjustment. To raise or lower
the string action, insert the correct Allen
wrench into the screw at the saddle (A). To
raise the saddle turn the wrench clockwise and to lower the saddle turn the
wrench counter clockwise. Intonation adjustments can be made by adjusting the
intonation screws at the rear of the bridge clockwise to move saddle back and
counter clockwise to move the saddle forward.
(A)
2
1
2
1
(FIGURE 1 )
(FIGURE 2 )
(A)
(B)
3
Mono-Rail II bridge allows the bass
strings to be isolated for one another by
using independent bridge plates for each
string. The strings are installed by
lowering the ball end into the bridge and
holing the ball end below the string catch
at the rear of the bridge. Intonation
adjustments can be made by adjusting
the intonation screws at the rear of the
bridge clockwise to move saddle back and counter
clockwise to move the saddle forward.
(A)
MONO-RAIL II
BTB
“Vari-mid” 3band eq
3band eq
2Band eq
Volume
Phat II EQ
SRX with PHAT II
phat eq
Each of the Ibanez pre-amps are specifically voiced to bring out the distinctive
tone of each model.
The strings are installed by lowering the ball end
into the bridge and hooking the ball end below the
string catch at the rear of the bridge. To raise or
lower the string action, insert the correct Allen
wrench into the screw at the saddle (A). To raise the
saddle turn the wrench clockwise and to lower the
saddle turn the wrench counter clockwise.
Intonation adjustments can be made by adjusting
the intonation screws (B) at the rear of the bridge
clockwise to move saddle back and counter
clockwise to move the saddle forward.
To replace strings, thread the new strings through
the string holes located on the back of the tailpiece
and bring them up and over the saddle. The
intonation can be adjusted by moving the saddle
forward or backward using a Phillips head (+)
screwdriver on the adjustment screw at the rear of
the bridge.
Staring height is controlled by using a wrench to raise or lower the small Allen
screws on either side of the saddle.
B400, B405 Bridge
RD
Standard Bridge
K5
EB10 5string bridge
DWB35
EB10 5string bridge was designed for easy
string change. The strings are installed by
holing the ball end into the string catch at the
rear of the bridge. The intonation can be
adjusted by moving the saddle forward or
backward using a Phillips heads(+)
screwdriver on the adjustment screw at the
rear of the bridge. String height is controlled
by using a 2.0mm Allen wrench to raise or lower the Allen screws on either side
of the saddle.
SR900/905
For slightly more sustain, strings can be
installed either from the back of the
instrument through the string grommets.
*Note: When replacing string check with the dealer to make
sure the new strings are long enough for the full scale length
of the bass.
Mid Boost/Cut
Balancer
Volume
Treble Boost/Cut
Bass Boost/Cut
Mid Frequency
BTB with VARI-MID IIIB 18V
Volume w/EQ Bypass Sw.
Pull:Bypass
Treble Boost/Cut
Bass Boost/Cut
GWB with BARTOLINI
®
NTBT
BARTOLINI
®
EQ
Balancer
Volume
Bass Boost/Cut
Mid Boost/Cut
Treble
Boost/Cut
SR with BARTOLINI
®
MK-1
Volume
Balancer
Style Sweeper
Finger Slap
Bass
Boost/Cut
Treble
Boost/Cut
SR with EQB IIIB STYLE SWEEPER
2way toggle EQ on-off Sw.
(RD900/905)
Volume w/Push-Pull
Pickup Coil Selecter Sw.
Balancer
Bass
Boost/Cut
Treble
Boost/Cut
RD with EQB IID
Balancer
Volume w/
Gain Boost Sw.
Pull:Boost
Bass Boost/Cut
Treble
Boost/Cut
DWB with EQB-DW IIB
Phat II EQ
Balancer
Volume
BTB with PHAT II
Tone
Front PU
Volume
Rear PU
Volume
SR, GSR with 2V, 1T
Volume
Tone
Balancer
RD with 1V, 1B, 1T
Volume
Tone
GSR with 1V, 1T
PASSIVE
Volume
Tone Character Switch
GAXB with 1V, TONE CHARACTER SW.
Front PU
Volume
Rear PU
Volume
Tone
ICB with 2V, 1T
Volume
Bass Boost/Cut
Treble Boost/Cut
GWB35 with EQB GWII
