manualshive.com logo in svg

IAI ROBO CYLINDER RCM-P, Operating Manual

Share
Download
IAI ROBO CYLINDER RCM-P Operating Manual Download Page 35

 

 

27

8-4-4 Data 

Input 

There are two methods of inputting the position data. 

(1) 

MDI numerically input ----- Method for numerically inputting the position data directly from 

the keypad of the Data Input Pendant. 

(2) 

Direct Teach ----- Method for allowing the position data table to read the position (current 

position) by turning off the servo control and manually moving the slider to adjust to the 

target position.      

 

In this section, we will explain an example of each operation. 

 

 

Caution:

  When the position data is first input by the method of Direct Teach after power-on or alarm 

raising, it is required to have homed the actuator in advance. 

The Data Input Pendant has no function of homing the actuator. 

Execute Direct Teach after completing homing RC by PLC in advance.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for ROBO CYLINDER RCM-P





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands