background image

 

ISH INLINE CONNECTOR Instruction Manual

 

Document No. 

HDM-0006 

 

 
 

 

20

  / 

22

 

Confidential C                                                                                                                                                                                                   

9. Unmating of connector 

   

Hold the female connector and push it in lightly. 

   

While holding the female connector in, press down fully on the end of the arm (see Fig. 39). 

   

Keep pressing the lock down, and pull out the female connector. 

   

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Notes 

Do not pull out the female connector without the lock arm fully pressed down.   
It may cause damage or deformation to the connector. 

Hold and pull the female connector (not the harness), when disengaging the connectors. 

If there is any damage or deformation, do not use the damaged item.   
Replace the item with a new one.   

Pressing down the front of the arm may not release the lock fully (see Fig. 40) 

 

Fig39. Lock arm 

Pull out female connector 

Direction of pressing 

Press down on the edge

   

Push point 

 

Push in lightly 

When the lock arm is pressed on the front part,   
center of the lock is bent. 

Fig40. Mechanism of the lock 

Press vertically with a thumb 

Good 

No good 

When the lock arm is pressed on the end, 
back portion of the lock is bent. 

Summary of Contents for ISH























Reviews: