background image

 

ISH INLINE CONNECTOR Instruction Manual

 

Document No. 

HDM-0006 

 

 
 

 

16

  / 

22

 

Confidential C                                                                                                                                                                                                   

 

6.How to release the secondary lock part 

   

Place the releasing jig into the secondary lock part taper situated at the bottom of the housing, and move the   

        jig to the direction shown in Fig. 30to release the secondary lock part (release one side at a time). 
 

   

 

Secondary lock part releasing jig: Part No. AP-0004-08-002 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

 
 
 
 
 
 

 

Notes 

Do not insert the releasing jig into any other incorrect place. 

Check for any deformation or damage on both of the secondary lock part and the housing after releasing the secondary lock part, before 
continuing any operation. 

If there is any damage or deformation, do not use the damaged item.   
Replace the item with a new one.   

Only use the secondary lock part releasing jig specified. 

Care must be taken when handling the secondary lock part releasing jig (it has very sharp edge)   

Care must be taken not to damage edge of the jig (e.g. from dropping, etc.) 

 
 
 

Fig 30.How to release the secondary lock part 

Releasing jig aperture 

Place flat surface inside 

Direction of release 

Secondary lock part releasing jig 

Summary of Contents for ISH























Reviews: