background image

GCHK-100 Instruction Manual         I-GARD

13

Control power:

 

5VA AC or 5W DC 
110-240 V AC/DC,

 50/60 Hz 

Maximum Range: 

 

-45% to +10% (60-264 V AC/DC) 

temperature Range (Celsius):

 

Operating Temperature: -40 to +60 
Storage Temperature: -40 to +80

dielectric:

 

Relay contacts to chassis:

 

1480V rms. for 1 minute 

Control terminals to chassis: 

 

1480V rms. for 1 minute

ground fault:

 

Pickup Settings (Amps):

 

 

¼, ½, ¾, 1, 1¼, 1½, 2, 2½, 3, 5, 7½, 10, 12½ 

Pickup tolerance:

 

–15%, +0% 

Delay Settings (Sec.):

 

0.02, 0.1, 0.2, 0.5, 1, 2, 5, 10 

Delay tolerance:

 

–2, +5 ms or ±2.5% whichever is greater 

thermal Withstand:

 

5000 Amps for ¹/³ seconds 

Harmonic Filter:

 

Low pass analog filter

Zero Sequence Sensors:

 

Toroidal, with window diameter up to 225 mm. 

Ratios supported: 

Any I-Gard T type ZSCS (e.g. T2-A, T3-A, T6-A and T9-A) 
1000:1, 600:1 and 40:1  
(Input impedance 50, 50 and 1 ohm respectively.)

ground Check:

 

Pickup Settings (ohms):

 

10, 20, 30, 50 ohms   

Pickup tolerance:

 

 ±20% or 3 Ohms  

Delay (for open loop and/or shorted terminator):

 

150 ms to 300 ms 

Fuse (½ Amp, time-delay):

 

Bussman FNQ ½ 
LittelFuse FLQ ½ 
Edison MEQ ½  

operating Mode:

 

Manual Reset or Auto Reset

Induced AC Withstand:

 

30V Continuous (at 25°C ambient) 
50V for 10 minutes (at 25°C ambient) 
60V for 5 minutes (at 25°C ambient) 
100V for 20s

frame Voltage:

 

Pickup Settings (AC Volts rms.):

 

40, 60, 80, 100 

Pickup tolerance:

 

–15%, +0% 

Delay (Sec.):

 

0.1 ±5% if voltage < 100 V AC.  
Less than 0.03 if voltage 

 100 V AC.

output Contacts:

 

Main trip Relay:

 

type:

 Form Z (NO and NC pair)  

Rating: 

   

10A @ 250V AC,  
10A @ 30V DC, 
½ HP @ 240V AC

Auxiliary Ground Fault Relay: 

 

type:

 1 Form C (NO/NC)  

Rating: 

   

10A @ 240V AC,  
8A @ 24V DC, ½ HP @ 240V AC

Auxiliary Ground Check Relay: 

 

type:

 1 Form C (NO/NC)  

Rating:  

 

10A @ 240V AC,  
8A @ 24V DC,  
½ HP @ 240V AC

terminal Contact Material: 

Clamping screw: nickel-plated brass 
Plug contacts: tin-plated bronze

physical:

 

Weight: 

 

GCHK-100 

855g 

 

 

GCHK-DRI 

45g 

 

 

mGARD-SYM 

600g 

 

 

GCHK-ZT 

35g 

Dimension:

 

See Figs. 11.1 to 11.4

Standards: CSa 

 

I-Gard reserves the right to change specifications of its 
products without notice.

10

 SpecificationS

Summary of Contents for GCHK-100





















Reviews: