ENG - 21
ENG
–
Do not use the device in places (e.g.
workshops, manufacture plants, garages or other
technical rooms
) where there are hot, flammable and explosive materials (e.g.
ashes, burning
cigarette butts, gasoline, diluents, dissolvent and aerosol fumes
) or lubricants (e.g.
fats,
oils
), chemicals, caustic agents (e.g.
acids, dissolvent, paints
). Sucking in the flammable
and explosive gases, the filters or the cleaner can be damaged or can cause fire, explosion
or electrical shock. The air is ionized by microscopic el. sparking (so called corona discharge)
which can set flammable substances on fire.
–
High voltage inside the device may cause electrical shock.
–
Do not use the device in industrial environment (e.g. kitchens). This device is not intended for
filtering oil or fat contained in the air.
–
Do not leave the device exposed to weather (e.g.
rain, freeze, direct sunlight and temperatures
exceeding 60 °C
).
–
Do not use textile or other materials (e.g.
drapes, curtains, blankets
) to cover this device.
If the air inlets and outlets are covered, it will cause abnormal operation and may lead to fire
or other accident. Do not put the cleaner on soft surfaces (e.g.
bed, towels, kitchen towels,
carpets
) while it is on.
–
It is not acceptable to adjust the surface of the appliance in any way (e.g. sticker wallpaper, foil,
etc.)! Do not spray the device with insect repellents or other flammable aerosol fumes.
–
To ensure flawless circulation of all the air in the room, do not use the device in niches, narrow
hallways or behind furniture, curtains, and drapes.
–
Place the cleaner in a way that the outcoming flow of air is directed into open space in the room
and not towards obstacles (e.g. furniture) or cold walls (danger of air moisture condensation).
–
Place the cleaner in a way that the outcoming flow of air is directed into open space in the room
and not towards obstacles (e.g. furniture) or cold walls (danger of air moisture condensation).
–
The device must not be placed directly under the electrical socket. I must not be placed in a
corner of a room but at least 30 cm from the left/right wall and the rear wall. At the same time it
must be placed at least 30 cm from various objects (in the direction of the outlets – flow of air)
to enable free air circulation.
–
There must not be any device with open flame in the flow of the air coming out from the cleaner
because of danger of burning process interruption.
–
Never let the flow of air blow on you (or animals) for an extended period of time. It may cause
health problems.
–
Check the correct position of filters. Otherwise the device can not be put to operation.
–
Do not handle the device if you have wet or damp hands.
–
Pay attention not to put fingers, parts of body, loose clothes, jewellery and other objects into the
air openings when operating.
–
Never look into the UV lamp or put your face near the front or back part during operation
–
To avoid overexposing to ultraviolet light, people and animals must be at least 30 cm from the
device. A short exposition to the light in close proximity is safe.
–
When bringing the device from cold environment to a warmer one, let it acclimate in room
temperature (approx. 5 hours).
–
Do not place the device near gas appliances, fireplaces and open flames. Not even near
fireplaces which are not currently in use. Dust and soot may circulate through the cleaner and
consequently settle in the device and the room. We do not recommend placing the device
nowhere near burning candles, paraffin lamps etc.
–
Place the device in a good distance (at lest 1 meter) from a computer, television or radio. You
can thus avoid interference and distortion when operating these devices.
–
Do not do the following: do not pull nor transfer the device by the supply cord, do not use the
cord as a handle and do not put the cord around sharp edges, corners or in close proximity to
a heat source.
–
Do not turn on the device if it is standing on the supply cord.
–
The device must not be left in operation unattended. If you need to leave the room, always turn
the cleaner off or turn it off and unplug it from the socket (always pull by the plug, not the cord).
