background image

1.4.1.1.7.      

 

Using the machine while fasten to fixed supports. 

 

1.4.2.

 

Improper use of the machine will invalidate the warranty, relieve the manufacturer from all 

liabilities, and the user will consequently be liable for all and any damage or injury to himself 
or others. 

2.

 

SAFETY REQUIREMENTS.  

 

 

2.1.

 

Your machine must be used carefully. 

2.1.1.

 

Symbols have therefore been placed on various parts of the machine to remind you of the 

main precautions to be taken. 

2.1.2.

 

Their meaning is explained below. You are also asked to carefully read the safety regulations 

in the specific chapter of this manual. 

2.2.

 

Replace damaged or illegible labels. 

 

 

 

2.2.1.

 

If you are using the machine every day in normal conditions, you can be exposed to a noise 

level of 85 dB (A) or higher. Wear safety glasses and hearing protection. 

2.2.2.

 

Do not leave the machine in the rain (or in damp conditions). 

2.2.3.

 

Read the instruction manual before using the machine. 

2.2.4.

 

Never throw used batteries into a fire - EXPLOSION RISK! 

2.2.5.

 

Read all safety warnings and all instructions. 

2.2.6.

 

Do not expose the battery to sunlight when the temperature exceeds 50°C. 

2.2.7.

 

Lithium battery. Never dispose of these batteries with household waste. 

2.2.8.

 

Do not wet. 

2.2.9.

 

Recyclable product. 

 

3.

 

SAFETY REGULATIONS 

 

 
 
 

 

 

 
 
 

 

Read all safety warnings and all instructions. Failure to follow the warnings and 
instructions may result in electric shock, fire and/or serious injury. 
The vibration value may vary according to the usage of the machine and its fitted 
equipment, and be higher than the one indicated. 
Safety measures must be established to protect the user and must be based on the 
load estimate generated by the vibrations in real usage conditions. In this regard, 
all the operational cycle phases must be taken into consideration, such as  
switching off or idle running.

 

 

 

 

The vibration value indicated was determined with a standardized tool and can be 
used to make comparisons with other electric equipment as well as temporary 
estimates of the load through the vibrations.

 

 

 

 

 

 

Failure to use this machine correctly can be hazardous for oneself and others. 

Page 4

Rev 2

Summary of Contents for HYC36LI

























Reviews: